Jump to content
Security Installer Community

al-yeti

Trade Full Member
 View Profile  See their activity

  • Posts

    9,576

  • Joined

  • Last visited

  • Days Won

    136

 Content Type 

Everything posted by al-yeti

  1. al-yeti
    Trump trump trump trump Musky supporting Tommy Tommy Tommy
  2. al-yeti
    Does bell work if you open cover Does bell work if you remove tamper at panel? Does strobe flash if bell doesn't activate?
  3. al-yeti
    does the bell delay state 0 mins is the bell in the same area (AB) as the zones ?
  4. al-yeti
    Grade 4.....lol
  5. al-yeti
    Resistor missing Back plate screw is my bet if it has one
  6. al-yeti
    Probably maintenance etc , holidays and all that Atleast it's sorted
  7. al-yeti
    Won't it update over the portal?
  8. al-yeti
    It's not modern tho , discontinued so better to return or don't buy it Get the ion40 range more or less same price The keypad adding can be stupid , power cycle and try again
  9. al-yeti
    It maybe your doing things wrong order? Eg partitions won't work without areas right?
  10. al-yeti
    But this panel still has those settings , where are you trying to example add a zone to A or D , are you using the usual way go to specific menu? What you mean by area numbers , where are you doing that ?
  11. al-yeti
    It took you time to understand my second comment second paragraph So good you worked harder and done it Everything you wrote here is irrelevant, if you have other technical help needed this is good place to start, except for defaulting codes and things like that
  12. al-yeti
    Good job , this was part of the effort ,hence first comment Although no need for service? Only time will tell
  13. al-yeti
    It will be engineer reset , scanny has this in menus to have certain elements reset by different codes, like other manufacturers , from memory it can also have a bypass method cat remember that how tho Hardly anyone locks those panels, except people like me lol
  14. al-yeti
    The problem with this is , when most make a mistake trying to do this , they wipe all the settings to default So if you couldn't find out how by now then try and avoid it, unfortunately this site does not give out that kind of information
  15. al-yeti
    Any local installer could do this for you, make contact and pay for service while your at it , full test job done
  16. al-yeti
    Nah they far behind Johnson controls ,I not saying they any good but .....
  17. al-yeti
    All panels will change due to market trying to catch up with ha even if it's in a basic way, I can't see any way around it
  18. al-yeti
    I did like that it had on pard lan port tho Unfortunately pros and cons of all panels , it's not easiest panel to work with But for you to butcher in a coma module it has space They are catching up at snail pace in my view , and getting left behind like Honeywell , many moving away to ha hub type alarms I think Is texecom planning this ? I bet they got some firmware issues hence why they quiet lol
  19. al-yeti
    Btw it's not a top notch panel tho I just saw that bit in your comments....
  20. al-yeti
    Yeah but this is all side issue and your talking about a small install Take the board out put one of your spare ones in and reprogrammed it End of story with customer Go get an rma from support send board in for repair or swap , they may even have spare board they will swap with you But I guess I am basing my support experience with hkc who are very helpful for installers
  21. al-yeti
    Nothing else? If you registered with them they will repair it if you send it to them ,they can probably write to it Although they might not do much .....
  22. al-yeti
    What did technical support say ?
  23. al-yeti
    I understand, I didn't think latest panels from texecom should do this tho but anyways
  24. al-yeti
    But your swb = special wintex build ? I sure Mr H and the rest could have some better meanings .... Lol
  25. al-yeti
    But then texecom always had firmware problems lol Just kidding Poor design to allow it write on the fly
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept