Trade Control Panels

If you hold an unprogrammed Pyronix fob to a Pyronix keypad does it beep?

I've been asked to look at an ADT system, but don't recognise it. Please see the photo. So, is this worth resurrecting, or should I be looking at replacement? If it is worth resurrecting, can anyone point me in the direction of engineers manual please? The current home owner does not have any keyfobs. Thanks in advance for any help again.

Here's a Euro 44+ I fitted many years ago T the last week or so has been an utter ball ache, one of the issues could have been avoided if could have UDL top this Is anyone using a euro 44+ with a webway or emizon ect... ?

personally I think its shit.... https://www.ebay.co.uk/itm/VISONIC-POWERMAX-PSTN-PROFESSIONAL-WIRELESS-ALARM-COMPLETE-KIT-UK-VERSION/350818930764?hash=item51ae70104c:g:h5oAAOSwbllch7ah

GoHow do I get the managers / user code back on G2 galaxy ? I have my eng code in it but quickly looked for option to change reset the managers code but failed to find it... Advice pls

Hi I've got a issue with a panel that I'd puzzling me I can full set the system but after time counts down not setting after final door shuts when opening the door a triggering contact on final setting the panel keeps beeping until it goes to intruder timeout then stops when master code entered when you go in first it riggers the system to disarm when entering the code the panel keeps beeping till time runs out why is this thanks

Hi folks has anyone got an. Installation. Manual for. The g2 12 galaxy with on board ethernet controller many thanks

all euro46 panels with 10.20s firmware are recalled for failing to perform. check all your recent installs. After a time they stop polling zones and fail to detect. a bit of a pain.

Suspised to see this in the DM appears to be a sales opportunity as well as a stabbing ?

From a recent thread re pyronix having rf issue with led street lighting. There was a mention of dual channel helping this issue? Anyone else having rf issues with different gear on led lights?

I know some wont like it maybe you need an app section anyhow hkc app control gates , heating etc, i dont understand how you get it to control ouputs on the app itself? cant see where the option is , any of you "three" done this, (say three because think theres not many hkc users here from the thousands of engineers not on this site) plus you must be bored of hijacking my other thread though i would start a new one

Yo dudes ok never done this bit when changing a panel over on an existing securecom site , on activation it reports it's already active on another site , how do you tell it to accept the new panel instead of the old panel, is this a securecom admin thing , bit silly if it is couldn't see option in smartlink to change it

At home I have an issue I haven’t resolved. I have an area D set which is programmed to Set on final door, this only works if I have the final door open before setting, if I have the door closed it goes to “quick setting”. I have only ever seen quick setting in eng mode. Any ideas? Area A works fine on final door set.

On a galaxy alarm output from the rio outputs are these classed as normally open or normally closed as I want to remove the dialler and add the spare outputs to. The cctv email alerts labeled up as intruder confirmed and power outage and tamper would I need to programme the dvr alarm input as no or nc thanks

I ran a cat5 to place a DVR on the network, there's no spare port on the router so made the executive decision to put small 5 way hub into the end station ,powered by the panel & converted to 9v now it didn't work out as well as I thought it would as the the little tp-link hub did not fit where the com2400 would with the cables in place, Converter board is stuck onto Hub, hub is stuck onto TCD, TCD is not stuck onto the endstation as the pads have been lost, ttl converter is also chucked in the endstation, battery is too small & bolt for lid is missing.... its rough as fuck but "works" The fog/mist was shocking getting there,…