Skip to content
View in the app

A better way to browse. Learn more.

Security Installer Community

A full-screen app on your home screen with push notifications, badges and more.

To install this app on iOS and iPadOS
  1. Tap the Share icon in Safari
  2. Scroll the menu and tap Add to Home Screen.
  3. Tap Add in the top-right corner.
To install this app on Android
  1. Tap the 3-dot menu (⋮) in the top-right corner of the browser.
  2. Tap Add to Home screen or Install app.
  3. Confirm by tapping Install.

al-yeti

Trade Full Member
  • Joined

  • Last visited

Everything posted by al-yeti

  1. So these have a little screw holding board in I think, you could take pic, remove 12v tape up and in turn each one tape up separately Then take board out only and swap over with other Some might say upgrade the pirs anyway and scrap it ......
  2. What pirs are they, picture? If it's possible you could remove the power tape them up and then swap boards over etc
  3. Yes , you don't have to use engineer hold off though , be careful with the power connections tape them to be safe and take a picture of how it was wired
  4. al-yeti replied to KWCFC's topic in Introduce Yourself
  5. al-yeti replied to KWCFC's topic in Introduce Yourself
    Remember the film "Falling Down"
  6. al-yeti replied to KWCFC's topic in Introduce Yourself
    You will be assimilated of course
  7. al-yeti replied to Peter1952's topic in Introduce Yourself
    Is this new ?
  8. al-yeti replied to Peter1952's topic in Introduce Yourself
    You have two power supplies? One for cameras one for recorder? What do you mean lost all night vision? Do you mean you had day pictures but no pictures at night? Maybe power supply being overloaded when ir lamps come on , so possibly power fault
  9. As the bods here taught me both have there uses , 24vac can be used further
  10. All nonsense , except you need it on very few sites
  11. I would say if you have time make a note of how it's wired, written and pictures Then wire up front bell as a single unit and try and get it to work Or if you really think it's front battery , change it, it's cheap And as above can you do this right...
  12. No detection in garage, means you can get to it without starting try tomorrow or full alarm
  13. Maybe there way of doing the tampers ?
  14. Diy stick both detectors on one zone and lash it in
  15. Serious you can't make two zones entry?
  16. Do you have engineer code? Do you have installation manual? Does the walk route from zone 3 go via any other zones apart from zone 1 ?
  17. Hmm I think I got mine in around 1995 or so aswell with an rs stamp on it Ok like the new tacwise though
  18. Model no and pictures of detector?
  19. 0.8v where? Cable fault? Do they share a cable?
  20. Not yet, but they just got hunters in Slough to start selling the hkc gear it's on there website for trade only no pricing Problem around this area is the £300 brigade will buy it and sell onto the public, total lunatics working for a cheap day rate Maybe just maybe, if they sell enough to trade they won't go with Joe public
  21. Getting to end solution
  22. You could in such and old system add a remote if the facility or local engineer is able to do it , if it has a key switch , with a few circuits added on
  23. Your in crack Cheaper to add wireless zones to house 20m doesn't mean anything , may I suggest you read your requests lol and don't be sensitive not trying to be smarty lol
  24. Ok fair enough fraggle , so your not interested in adding a wireless zones to the garage which maybe cheaper on longer run, if system is maintained as you say will be not much more expensive on service

Account

Navigation

Search

Search

Configure browser push notifications

Chrome (Android)
  1. Tap the lock icon next to the address bar.
  2. Tap Permissions → Notifications.
  3. Adjust your preference.
Chrome (Desktop)
  1. Click the padlock icon in the address bar.
  2. Select Site settings.
  3. Find Notifications and adjust your preference.