Jump to content
Security Installer Community

al-yeti

Trade Full Member
 View Profile  See their activity

  • Posts

    9,444

  • Joined

  • Last visited

  • Days Won

    129

 Content Type 

Everything posted by al-yeti

  1. al-yeti
    Those panic buttons look nicely used lol, someone after you lol
  2. al-yeti
    So garage has no detector? Maybe sensor playing up, when did you have system service last? Requires some investigation really , seems your circuit is split , but if it's a tamper fault of some kind , while set can show as alarm from what I rember on those
  3. al-yeti
    You got dialler on redcare? Leccy must be JB CCTV looks like a 2k job up north
  4. al-yeti
    Lol ok I thought moleys would be harder But yeah short piece , especially you pinch end a bit to make it a nice fit
  5. al-yeti
    Lock Smith's carry a tool slides over cylinder end tilt up and down fees seconds your done I didn't have patience to watch video lol if that's what he did
  6. al-yeti
    Common , no one cares though , they keep putting the standard cylinders everywhere
  7. al-yeti
    One of your Refurbs?
  8. al-yeti
    Police say don't lock internal doors as they cause allot of damage Personally nice loud internal bell , no open plan layout and lock them doors to slow them down , hopefully they just raid the fridge
  9. al-yeti
    Funny that, customers won't even pay for a new cover to make it atleast up-to-date , but they do worry about those knight rider lights
  10. al-yeti
    Or disconnect the mains and battery in one hit , see if the bell dies after a minute , otherwise put power back and do above as they said
  11. al-yeti
    Yello
  12. al-yeti
    Of course if you get threatened it's lashed in at half the price
  13. al-yeti
    120 a day he gets it lashed in time for tea
  14. al-yeti
    Chimney breast no big deal , you don't have perimeter protection so intruder would access room either way and trigger it once in I would move it first personally
  15. al-yeti
    Read more: Swap the quads positions with the dt see if problems follow the quad , although as above need to see or have systems described more Must be reason you opted for duals in other rooms, perhaps list rooms with sensors and why you chose what to go where
  16. al-yeti
    Did you setup individual users on DVR?
  17. al-yeti
    So you need to know what ports your DVR uses , those ports need to be setup in the firewall section of your router by creating rules , then those rules would be applied and asked to be sent to your DVR IP address You may need to set your DVR to a static IP setting if your router does not allow you to port forward via Mac addresses
  18. al-yeti
    Damaged data line , has to replace.cable at some point
  19. al-yeti
    I am near Heathrow , house bashing for a living unlike these alarm monkies sitting behind a desk
  20. al-yeti
    How much hey charge , example?
  21. al-yeti
    Do you mean default codes do not respond ? Or Keypad in a whole does not respond no bleeps no lights nothing ? Or frozen like with lights on? Has it been a year since you last tried using the alarm?
  22. al-yeti
    How did you delete it
  23. al-yeti
    New build all with spots loads of them plenty of cavities Unless they opt for single light
  24. al-yeti
    Probably something like wrong polarity or output connected to dialler , so when you disarm it is sending the trigger to the dialler Assuming it's an external dialler and so on If it's old system did you change settings somewhere ? Or new and not sure how triggers and outputs work so wrong connection
  25. al-yeti
    If you mean the enforcer , it has an output board and it's labelled kind of different on how to use it and what you can do with it Throws all the diyers into paying for bell part to be installed by engineer these parts
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.

  I accept