Guest Forum

how do i change the entry/exit time on the veritas 8

I have just purchased a new house and an alarm system is fitted. A Veritas Security Panel. All is okay but I need to change the configuration of the programming of the part guard settings. I need an installation manual.. Thanks Steve Email steve@palin1.co.uk

Our veritas v8 is 3 and a half years old and h recently started going off when not set. It occasionaly makes very short high pitched alarms when unset too. Any ideas?

Having lokked in the control panel to see which wires go to the flush contact on the door I now have a tamper light indication on the control panel - The user manual says contact the installer (who are now no longer in business) How do I reset / remove the tamper indication from my control panel (Scantronic 9448) - Thanks in anticipation Allan

Is it possible to change door mounted allarm contacts in a wooden door for surface mounted cntacts on a replacement UPVC Door

Hello Great site you have here, lots of decent advice/info. Signed up a few days ago, but had no vaildation e-mail through (tried the resend button, but no joy). Anyway I'm after a new or used (along as its in decent cond) //.National Installer.// or Chubb bell box. If anyone has a spare floating about they want to sell I can be contacted by email on: jackcarter_71@yahoo.co.uk - I'm in the West Midlands. Thanks, Jack.

can anyone advise me on a good fire alarm panel and were to get it has to be a fore zone

Can anyone help please? We have moved in to a house that has an //.National Installer.// alarm fitted (Don't know the model number but was fitted new in June 2003). We are having the house entirely rewired and want to have all the alarm wires (e.g. door contacts/PIRs etc) chased in to the walls as they are currently surface mounted. This is bound to involve some rewiring of bits and pieces etc - the alarm company (//.National Installer.//) has said that they won't chase wires into walls and the electricians are uneasy about touching some other company's alarm in case it all goes wrong - does anyone have any suggestions e.g. is DIY simple enough on these things as I d…

just bought a house and it has a veritas 8 based alarm fitted the alarm did eaxctly what it was supposed to do only problem is that it only had to pir's both wired to zone 1! so i decided to add magnetic door sensors etc i presumed this would have been straight forward i've placed all the sensors where i want them i decided then to test the first sensor i.e zone 1 so i disonnected the power and the batt i then held the tamper switch down and reconnected the batt but it keeps beeping stop for a sec and starts again, the sensor function as the zone show open and closed when front door is opened an closed, an ideas?

iv just started work on some flats i have that have a zircon single loop addressable fire panel in fitted. The problem is i don,t have a manual for it and when then power was swiched back on the panel started to beep. dos anyone have a manual for this panel or could tell me how to mute the panel.

i just moved into a property that has a veritas 8c alarm and the last tennant didnt leave the code so i am unable to use the alarm. Can anyone help? Also can anyone send me a manual

i just moved into a property that has a veritas 8c alarm ....and have replaced all the windows and doors. On the old windows and door were alam sensors which have just been cut off to make way for the new windows and doors. I just want to get the alam system back up and working just off the room sensor ..I have never been giving an instruction manual for the system so any help finding me one or any tips to get my system back up and runing would be great ...email me at ...maxs@erection.freeserve.co.uk

can any one give me any info or manuals for this fire panel iv all ready looked at the info on the bardic web site and could no get hold of a operating/user manual for this panel

could anyone tell me a few good places to by fireturf cable

has anyone got a copy of this manual that thay could send me ?