sixwheeledbeast

Also look at the local arm and disarm options.

Hang on, is this a Premier 24 or a Premier Elite 24. Elite's have two areas, non-elite this won't be possible.

Introduction Having used Optex detectors for years, I thought I'd review the two latest versions of there Quad PIR against each other. From the manufacturer... SAVER RXC-ST Design, construction and packaging Firstly the packaging the SAVER coming in a plain box and the Core series in a blue printed box, this is larger to a accommodate a ceiling bracket. I am not keen on the packaging for the SAVER, well I say packaging I actually mean the fact it has SAVER printed in bold on the box. Stupid name for a detector; in my opinion. The two sensors have a similar construction, manufactured from a sturdy white plastic they have that classic Optex style and feel using the same lens as the RX40. They do not feature a separate LED window unlike the RX40. They have a relatively small case and would be fairly discreet mounted in the corner of a room. Both sensors have a small cross head screw located on the bottom of the sensor. This has to be completely removed before the lid can be levered open. This is annoying as the screw likely to be dropped and roll under something or lost. Inside the sensors look identical, with loads of room and plenty of easy to use knockouts and cable entries. It also has a large channel up the rear of the back plate to accommodate cabling behind the sensor, if mounted flat. Optex always provide a small piece of sponge with there detectors, this should be used to seal the cable entry hole. Operation and setup As I mentioned already there is plenty of room inside which makes installation a breeze. The screw terminals are good quality and provide secure termination of stranded alarm cable. There are even two spare terminals which may come in handy depending on the installation, something the RX40 lacked. The detectors do not have built in resistors which is a shame. Most detectors have this now and it could put people off installing them. The instructions provided in both are very clear and explain not only product specific information but general tips of good installation practices and siting. Again both sensors provide the same sensitivity adjustment High, Medium and Low located to the left of the PCB with a three pin jumper configuration, this comes set to High which in clean environments shouldn't be an issue. They perform very well in all three sensitivity settings with a noticeable difference between High and Low. Low however, is still very capable of detecting an intruder. On detecting movement the lenses light up with a red square, this is more noticeable than a LED prism used on other sensors; especially in a brightly lit room. There is a jumper provided for disabling this if required. Conclusion The detectors are very good and perform well with no faults or false alarms. I can't see any obvious differences between them apart from the front lid design and bracket provided. Likes *Plenty of room for termination *Same lens as previous models Dislikes *Lid screw easy to lose. *No EOL jumpers *SAVER name

Links into Elan pretty easy if you understand it. But IMO as an alarm system it's a bit pants and not really designed for the UK market.

Thanks for reminding me, I need to dig out my card

I am also thinking the best way would be to keep it separate. How about an IP encoder/decoder if it's really awkward to put your own cable in.

Two live boxes could have been too much current and blown something. Most panels need additional PSU's or SCB mode for multiple sounders.

Series the tampers, parallel the others. Deltabell will have wiring diagrams. Will your system support two live boxes, most won't and require additional power supplies or SCB mode.

Assuming requirements are met, that is.

Been "red spotting again" Yes, I know the pictures pants but it was the other side of a dual carriageway. Chester Road (A556) Rostherne Cheshire http://goo.gl/maps/gYEmL

No failures on any Techwin stuff here.

Not fitted that model but have fitted 600TVL Varifocal Techwin bullets before. I like them.

Wilderspool Causeway/Stafford Road/Greenbank Street Wilderspool WA4 6RP http://goo.gl/maps/7bqRi Signs can be seen from Morrisons Car Park.

Drove past today.

I thought that's where this was posted?

Well, seems the signs are still popping up, spotted some at Wilderspool Morrison's. Still has the NSI logo on. Will have to get a shot next time I am round there, not as good at hiding behind a HP bottle as Matt is.

An additional power supply is not required and you do need the correct expander card. I would still use Low Current and/or SCB mode on the bell myself to reduce the current drawn by the sounder. The expander card comes with instructions, it requires an EOL resistor in the sounder but other than that it's simple. Yes, the GSM sends the same type of signals as PSTN, text message have zone information which is good. You have to set them up correctly with test signal enabled otherwise the SIM will expire. This is a one-way systems so not the most secure, would have to be a low risk site IMO.

I'd always wire one 8 cored cable to each detector, even if you are only using 4 cores. Screened cable is not required for anything on Texecom and yes IMO it is top quality stuff. Smokes could be wired together on Latch but TBH it's not worth messing about like that. Stick with one zone, one device, one cable. It seems extra keypads have been mentioned I would say one upstairs on the landing will be handy. It means in the night if the alarm activates you can locate the room before storming down the stairs. One in the garage maybe pointless if it's not large enough for a car. Maybe you could install the Hall keypad on the Hall/Garage wall then you only have to drill through to install a keypad in the future. Remember any final exit door should have a contact on it to trigger the Final Exit. Obviously cables installed to places for future expansion is handy but it depends how much protection you need. Have you thought about a fixed PA button in the master bedroom or adj front door?

I agree with above too. Speakers up and down for the system tones. Positions look good, use Quad PIR's for the house and a DT in the garage. Depending on the garage door it's best to use a roller shutter type for this Also bear in mind how much current all that will take, you may require a PSU. You may as well use a Premier PSU200XP as you are already over 8 zones.

Why are the sensors in the middle of some rooms? The kitchen isn't covered, I'd put one on the landing too myself. Smoke in the downstairs hall? Use a DT in the Garage Any pets we should know about? Nice drawings BTW.