Nova-Security
-
Posts
3,344 -
Joined
-
Last visited
-
Days Won
24
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by Nova-Security
-
-
Bell-----Panel
0v A
12v D Bell +
S- B Bell -
STR Strobe -
TMPR T SCB
link 0v to TMPF in the bell
-
Put a LED no resistor across the 485 pair and it should pulse when telemetry commands are sent.
Hard reboot of the camera, you have probably lost all programming and will need setting up again
-
1 hour ago, james.wilson said:
id agree max, but wasn't the max4 grey and the 3 black?
yes, i got it the wrong way around
-
looks very much like a worn out galaxy max3 reader
-
Galaxy G3 can have individual reset levels for different faults
-
14 hours ago, PeterJames said:
Down power completely power up mains first then battery close box, enter code, press reset
-
Thanks
Spoke to them yesterday and that's what they said.
-
Anybody know how to reset the admin password?
-
2 hours ago, sixwheeledbeast said:
Leaving Guardall values at a device will mean the resistance is 4100 ohm secure and 8200 ohm active, this does not allow for any tolerance of the device or cabling either.
isn't Guardall 8k2 normal and halfs on activation ?
-
7 hours ago, Jim Randle said:
Guardall use EOL 8K2 in parallel. I've changed a few out to Texecom Elite panels and left the EOL's as Guardall values. If you program the panel zones to 4K7/4K7, it works fine. Jim
Didnt know that
-
1 hour ago, RichardSalford said:
ADI budget stuff WBOX says it offers DDNS but that has also expired.
Could be due to the fact that its HIK rebranded
-
If unsure dont even attempt it, these are a proper panel and there are loads of things you need to do just to get it working
3. Setting up the Advisor MASTER control panel
There are several options that must be programmed into the Advisor MASTER control panel before attempting to use TITAN.
Follow these steps:
a) When connecting the panel directly via the J18 (on-board RS232 port) or connecting the panel via the ATS1801 computer/printer interface, it is not necessary to set the following menus:· Menu 29.1 (Enable Remote Up/Download)
· Menu 29.2 (Up/Download if any Area Armed)
· Menu 29.3 (Enable Remote Control)
· Menu 29.4 (Remote Control if any Area Armed)
b) Every Advisor MASTER control panel has address ‘0’ as the default. When operating in multi panel configurations with 2 or more panels (only applicable with TITAN Security System Software) you have to set the corresponding panel address in the menu 'Computer Address'.
To ensure optimum security, it is advisable to select the following options for menus 29.1 to 29.4:· Menu 29.1: YES
· Menu 29.2: NO
· Menu 29.3: NO
· Menu 29.4: NO
c) In Installer programming menu 29 (Computer Connection), note the Security Password for each Advisor MASTER. This needs to be entered in TITAN for each Advisor MASTER to enable connection to that Advisor MASTER. If the Advisor MASTER also has the Security Password Attempts option, make sure this is set to 255.
Once these options are correctly set up, continue with installing TITAN. -
no its Aritechs UDL software
-
-
Inline flow switch
-
The Rf Portal should be flashing but depends on the rate
0.1 ON / 0.9 OFF Normal communication
OFF No d.c. supply
1.5 ON / 1.5 OFF RIO has not been configured into system
0.2 ON / 0.2 OFF RIO has lost communication with system
0.9 ON / 0.1 Very poor communications
If you have access to the programming menu check RF module comms in 61-3
-
13 minutes ago, james.wilson said:
id like that please?
Same here
-
19 minutes ago, GalaxyGuy said:
You're using the black Honeywell etched fobs and adding the etched number manually against the user ?
9 minutes ago, danlad1980 said:the fobs was added via the touch screen by adding a user then pressing learn card and holding the card to the screens prox.
For Max readers you have to enter the code on the back of the fob manually as GG post above, not by pressing A+1 and presenting to a keypad. Only the thin fobs will work with max readers
-
Accenta's had comms outputs and the anti-code was there to conform to ACPO requirements for a managed reset before DD243 came out.
- 2
-
47 minutes ago, ritabix said:
I let adata technical use my PC on let me in on many occasions, notably on the last two days of trying. I was told after lots of hours if this doesn't work then it won't work. Unfortunately that was that. I have only been in contact with my suppliers since then. Thats CEF and they are trying to resolve some compensation for the whole Che-bang. I wont be using Adata ever again and I'm going to make it my retirement hobby to make sure people know my story and that of other security companies who are of the same opinion, and thats only in North Wales.
So the Blame lies with CEF, who specified the kit?
Out of interest post the model mumber's of the kit you have
-
A analouge camera with separate zoom lens ?
-
So its a standalone wireless bridge not going on the wifi network, probably some IP settings you have wrong or alignment of the equipment.
An access point to pick up the sites wifi would have been another option but putting in your own link in will be better.
-
26 minutes ago, BUSTER said:
Peter Blair
Very nice man, our first inspector
-
Hi all!!
in Introduce Yourself
Posted
Hi,
Resolve Dept by any chance?