Nova-Security

Galaxy G3 can have individual reset levels for different faults

Thanks Spoke to them yesterday and that's what they said.

Anybody know how to reset the admin password?

isn't Guardall 8k2 normal and halfs on activation ?

Didnt know that

Could be due to the fact that its HIK rebranded

If unsure dont even attempt it, these are a proper panel and there are loads of things you need to do just to get it working 3. Setting up the Advisor MASTER control panel There are several options that must be programmed into the Advisor MASTER control panel before attempting to use TITAN. Follow these steps: a) When connecting the panel directly via the J18 (on-board RS232 port) or connecting the panel via the ATS1801 computer/printer interface, it is not necessary to set the following menus: · Menu 29.1 (Enable Remote Up/Download) · Menu 29.2 (Up/Download if any Area Armed) · Menu 29.3 (Enable Remote Control) · Menu 29.4 (Remote Control if any Area Armed) b) Every Advisor MASTER control panel has address ‘0’ as the default. When operating in multi panel configurations with 2 or more panels (only applicable with TITAN Security System Software) you have to set the corresponding panel address in the menu 'Computer Address'. To ensure optimum security, it is advisable to select the following options for menus 29.1 to 29.4: · Menu 29.1: YES · Menu 29.2: NO · Menu 29.3: NO · Menu 29.4: NO c) In Installer programming menu 29 (Computer Connection), note the Security Password for each Advisor MASTER. This needs to be entered in TITAN for each Advisor MASTER to enable connection to that Advisor MASTER. If the Advisor MASTER also has the Security Password Attempts option, make sure this is set to 255. Once these options are correctly set up, continue with installing TITAN.

no its Aritechs UDL software

https://www.tlc-direct.co.uk/Products/ESKITSP3TRI.html?ad_position=1o1&source=adwords&ad_id=45425533757&placement=&kw=&network=g&matchtype=&ad_type=pla&product_id=ESKITSP3TRI&product_partition_id=174054196627&test=finalurl_v2&gclid=COuLnI3w4tICFQoo0wodRHQPAw ESP...........No thanks

Inline flow switch

The Rf Portal should be flashing but depends on the rate 0.1 ON / 0.9 OFF Normal communication OFF No d.c. supply 1.5 ON / 1.5 OFF RIO has not been configured into system 0.2 ON / 0.2 OFF RIO has lost communication with system 0.9 ON / 0.1 Very poor communications If you have access to the programming menu check RF module comms in 61-3

Same here

For Max readers you have to enter the code on the back of the fob manually as GG post above, not by pressing A+1 and presenting to a keypad. Only the thin fobs will work with max readers

Accenta's had comms outputs and the anti-code was there to conform to ACPO requirements for a managed reset before DD243 came out.

So the Blame lies with CEF, who specified the kit? Out of interest post the model mumber's of the kit you have

A analouge camera with separate zoom lens ?

So its a standalone wireless bridge not going on the wifi network, probably some IP settings you have wrong or alignment of the equipment. An access point to pick up the sites wifi would have been another option but putting in your own link in will be better.

Very nice man, our first inspector

https://www.broadcastwarehouse.com/barix/instreamer-and-exstreamer-100-audio-over-ip/84/product

Are you allowed on to the wifi network? If so look at access points, and you will probably need agreement with their IT company and some static ip addresses assigned for the cameras. Whats the kit you have already ?

I think some of the guys are original molynx/bewator based in cardiff also

Try Williams http://www.w-e.co.uk/index.php/contact-us

WTF 4 door ? Orignal Colin McRae £375,000 https://www.motorsportauctions.com/category/329/Historic-Rally-Cars/listings/36108/MG-Metro-6R4-ex-Colin-McRae.html

No We only use elmdene, only had faults like this with handed contacts until we swapped