al-yeti
-
Posts
9,147 -
Joined
-
Last visited
-
Days Won
117
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by al-yeti
-
-
I suppose allot to do with location and perhaps being able to switch at each point, then still asbove one Dvr , a switch , or loop through monitors instead of tv's , lots of good ideas above!
More detail perhaps needed
-
Check user attributes perhaps
But you confused matters, earlier you said after an alarm it wont unset, or you mean wont unset in general
-
Informa will dial without a filter but worth a try , maybe you can also check the polarity if itvm helps
-
Doesnt the managers password allow you to change the user password level?
-
What's the italian message saying?
-
Still no luck with what? I thought it was dialling and calling you with only problem being the tone in tandem
Question, does it ring your mobile? The informa , if yes no need to open the main panel, it has to be the dialled
Question, do you mean the informa is "dialling" but you mean tries to dial and as it does so the engaged tone comes up?
The informa starts playing the message as soon as it starts dialling that's normal for it
So same question when you say it dials, does it actually get your mobile to ring? If not then as I said before your getting an engaged tone when informa is dialling out and has to be to do with the line
Ok I think reading over you mean the informa performs the dialling operations but does NOT actually dial out because the line is not allowing you to dial out, engaged tone means line restrict for some reason
Inability to dial landline numbers means your line is restricted to incmoning only, please read over this thread again
-
Even with 9651 you can add a sounder or second keypad upstairs although hallway speaker you should hear to, your better off with the 9751 , as later if you expand the system easier and less hassle
-
So basically the informa calls you when the alarm activates and works with the addition of a beep or extra tone in tandem with message
I assume you tried deleting and recording new messages again? Incase that is corrupt somehow?
I got confused because of title ie "not dialling"
-
side point is your new provider restricting your calls ie incoming only hence wont actually dial out to anything? so you might to check that
-
You said " Today, I have been running tests on the dialler and everything functions as it should"
But you also say its doesnt dial out on alarm?
So to me it sounds as if there is no dial tone on the informa or it isnt seeing the dial tone, i assume your phone is a standard phone? or is it an ip phone connected to the router? which might make sense why that wil still work, if thats the case what happens if you plug in a standard phone
might be wrong but inof didnt add up above unless i read it wrong
-
How much is this all costing you, just thought other panels do a better job at same cost
-
Hope so dont like the plastic box, maybe they giving a free external antenna for the rf card?
-
Are lines Tracing all objects ? Ie around the house aswell or only certain colours
-
ok are you saying when you turn of the mains the outside or internal bell starts ringing? battery you mean internal battery?
Just turn power off and remove the external or internal bell, or get an alarm company into to do it for you, they probably can service it and get it going for you possibly
PS because battery is dead its quite normal for the bell to ring because the bell still holding power even without power from panel
-
I have seen that on startup not sure why, but it shouldn't occur again once your setup and running, It may occur if you default the system aswell
-
Only issue with the texeco m dialled if for any reason bell signal drops it will stop dialling so better to connect to something that will only reset with code or tag, ie strobe or another intruder output , I suppose its only if it didn't get hold of anyone within the bell time but I found it better to avoid the bell output with this dialler if it's set to code Or reset to stop signalling , or its another dialled your talking about
-
Shouldn't this have moved by now? General population might not understand the discussion and take it the wrong way
-
Compliant for diy install? Or self monitoring?
-
Just install a Dialler / gsm unit or both , i am in heathrow if you want it installed etc PM if you like , wont charge you the earth!
-
How about
- to - hold off
+ to + hold off
-rtn to t (tamper switch return)
I assuming trg and stb are bell and strobe just join both to s
Although I thought there should be another output to seperate them this will still work as both should be negative triggers meaning if you have more than one terminal for the strobe connect to the - minus one
Didn't look up the panel but someone can confirm
-
LCD version accentia g4 just as cheap diff panel , don't see why anyone buys the led type now,
Agreed shoot who designed programming, slight difference on some of them with one key changing codes aswell
-
oh well , the who is search on the domain leads to a company called http://www.procuredirect.co.uk/ same phone number? looks like some time of electrical wholesaler going into alarm market
-
Oh I was referring to the trade dept, honeywell techs Muppets to
-
Default whole panel
Castle Care 1600 Alarm Control
in Members Lounge (Public)
Posted
Hi, as Norman said but you have to be in manager mode to change the user code, page 13 read it again please, read bit about selecting user to change its code whilst in manager mode