Trade Control Panels

Went to the Northern Motorhome Show in york and found a stall selling these alarm systems. Found this web site... http://www.siemens-mobile.com/repository/7...20Datasheet.pdf (It takes a few minutes to down load.) Just wanted to know if anyone had come across them. They were being sold through Catch Monitored Security Ltd. B.

scantronic 8136 can anyone tell me anything good about it?????? (this should start the ball rolling!) regards Paul. Ive copied this over from the Nacoss section for Paul so heres you chance lads!!

Had quite a few Castle Care-tech Euro-Meridians with a Digi-fail on the main panel recently. Bascally means that the modem has been unable to connect to the ARC. This requires a customer code to silence. When going through the logs on these panels, I have noticed a number of line failures - each of 2 seconds duration, and approximately 8 days apart. Always between 2100 and 0300 hrs. On one panel, BT have admitted a fault and corrected it, which has resolved the issue, but on the others, BT deny any fault and want to charge the customer to investigate. Anyone else come across this?

Georg in trouble.. How to program Gardtec593 digicom to make a call to prive line/ mobile phone? Any suggested method to do that? I am using 593 first time (before i have been using DSC585 for small installationd and used comms format 06 (private line)).. Digicom just makes a call after call. Naturally because it cannot get Handshake + ACK. Is there possibility to make those signals by DTMF or how should I program it?

Hi guys I`ve just had an email from Ian Avery at guardall. If any of you use the Guardall stuff, could you please spare a few minutes and add a few reviews. What can this all singing Guardall do that a Galaxy cannot..? Thanks Guys. Add a Review

Anyone who wants to share an opinion about it?

Since Add8 asked for: "Excuse my ignorance, whats better filtering? Only asking as I've got some issues on a G/T ID system we took over recently that keeps F/A ing, and checks out ok on Technicals troubleshooting guide. Anyone want to PM me with ID info / known prob's or even kick a topic into the Trade Forums for discussion? This post has been edited by Add8: Oct 12 2004, 09:40 PM " The maximum cable distance is 100mt from the ID card. This one you run with alarm cable. With the G/T panels you can mount the ID card 500mt away from the panel using screened bellden cable (Belden Cable type 8723 AFAA 22 AWG (7/0.25mm T/C) 4 Wire (2 Pair) LSF Sheathed). Then you have 1…

I went back to an install today to commission it and found that when I touched (with a slight twist the pcb) all the 13v outputs failed. Obviously checked the fuse, but it

I guess everybody knows my opinion of wireless things.. Anyhow, I got call to service Visonic powermax PA buttons, which they say make FA:s themselves when nobody touches them. Any trobles with anybody with this equipment?

Does anyone have a good idea for setting/unsetting the alarm when there is plenty of workers who don't know if they are last to leave or first to come. I have used FIRST IN LAST OUT option in the control panel. This means that everybody uses his/her code + adequate button to tell the control panel when entering or leaving. CPU the sets/unsets alarms regarding accesslevels (partitions the user has access to). Keypad filter can be used so that even if user has access to all partitions, that keypad allows only to disarm partitions spesified for that keypad. Anything like this in UK - markets? Any Accesscontrol that could do this with a reader pair?

swapped main pcb on a 8136 when im trying to come out of engineers getting the message: "initialising system please wait" then "zone 122 missing" there isnt a zone 122 though,and after this happens i have to remove mains and battery to get out of it. A bit of head scratching going on,never been my favourite panel right enough. Anyone any ideas

Ok, I'm a dozy git! How do I get out of engineer mode in a Sterling 10? Can't see it anywhere in the Instal Manual, and I don't normally use this make of panel. (It's an LCD RKP if that makes any difference) Regards, George

Morning chaps, Does anyone (must have) experience of tamper faults on an 816? Wiring installed by myself a few months ago so I know thats ok, one PIR is giving tamper alarms, twice now in 2-3 months. EOL wired, do the resistors cause problems does anyone know?

Does anyone know how to turn off the chime at the end of the setting or partset.I don't have the full manual but can work my way around if someone can tell me were i'm going?

Performed a NVM reset on a 9450 last night, re programmed no problem. Last night: Customer happy This am: Panel not taking code. Seems to have lost memory...again. Misc details: Bell box knackered, customer refused a replacement, system installed by norweb, 1989. Told her the panel is prob knackered as well, didn't like that! Anything on the NVM i'm missing?