Everything posted by james.wilson
-
What does a speaker output do?
yes most panels have a speaker output for alert, setting unsetting, chime tones etc. Some panels this is a switched output like a bell on others its a speaker output usually for a 16 Ohm load
-
Honeywell FX100+ Post-Install Question
Oh never used a flex thanks gg
-
Honeywell FX100+ Post-Install Question
Agreed but we use level 3 normally and what you have doesn't happen. So I'm concerned there is something else happening
-
Scantronic 9448+ Tamper LED on
Isn't the iwise bus a bus detector that will only work on a risco panel? You have also probably blown the fuse or panel. Wires shouldn't 'touch'
-
Hello from Midlands
Hi and welcome
-
Honeywell FX100+ Post-Install Question
There is something g else there as a level 2 user doesn't have menu access. How are you or were you u setting it
-
Honeywell FX100+ Post-Install Question
its going into the user menu. It shoudnt do that unless the code is being entered twice. You also shouldnt be seeing 'boot-up' as that is saying it has restarted
-
eBay tat roundup - the best and worst from the 'bay
Wtf would anyone want it
-
Greetings from Australia
That's a walk test but you do need to test it and fire the external, signalling etc
-
Honeywell Galaxy Flex 100+ Exit Engineer Mode Issue
The missing key missing max means something addressed 1 has been lost. Using that video won't help with miss g 485 devices
-
Greetings from Australia
Didn't know there was an option for non eol on a galaxy. To display the diagnostics go into the display zones menu it will show in there
-
Honeywell Galaxy Flex 100+ Exit Engineer Mode Issue
If its addressed as 0 then it's not device 11 Have you changed the address while the keypad is powered up? Try rebooting the panel it will then only connect to devices that are online
-
Greetings from Australia
in fact looking again neither will work Have you got NO or NC reeds?
-
Greetings from Australia
well the top one wont work both resistors would need to be at the panel and one of them in series with the reeds but even then your asking me would i prefer a 6 inch nail or a 4 inch nail in my foot if you see what i mean
-
Greetings from Australia
It will work but won't have any tamper protection
-
Greetings from Australia
looks like you need option 14 and NO contacts to use a single resistor. else wire cuts wouldnt be detected
-
Greetings from Australia
on the dimesion you can select resistor values per circuit id assume you can on this this too, but ive never done it
-
Greetings from Australia
Eol resistors are for End Of Line use they shouldn't be in the panel expander etc. If the flex supports seol then you would out this at the end. I haven't looked in detail at the existing wiring
-
Solid State Smoke/Fog
No and it's a issue I hear I bsia meetings. The lad from smoke screen is very active in Europe regs wise from what I hear it won't be long till they are banned throughout Europe. But ask Carl I don't engage in any of that as I don't have anything useful input wise
-
Honeywell Dimmension Galaxy 48 firmware upgrade
Buy a spi key
-
Solid State Smoke/Fog
To be fair it's fully licenced by Mr Wong. Based in China registered address used to exist
-
Solid State Smoke/Fog
probably not, plus id check with your insurer to see if your covered to install chinise made bombs in customers sites that dont have any uk based safty certs!!
-
Solid State Smoke/Fog
lol
-
Greetings from Australia
Normally your final exit doors would be 'final' you entry route zones would be exit. The use intruder for the rest not on the entry /exit route
-
Solid State Smoke/Fog
Dunno what it is? I was only aware of the glycol or pyrotechnic based ones