Nova-Security
-
Posts
3,344 -
Joined
-
Last visited
-
Days Won
24
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by Nova-Security
-
-
Mostly using RSS for the setup - but via the ext rs232 as i cant get the ethernet connected yet.
ADT have their own firmware, on some 144 and 520s the spi key didnt work and other options where disabled, if you have an old ethernet module the firmware in the panel might not support it as its to old.
True , there is the odd one used , most marked new when they pop up
They got more things to worry about than all that equipment on eBay
ADT manchester have an office looking through Ebay and social media
-
Its a new panel - possibly destined for an ADT install as the banner is preset with ADT etc.
Buying stolen property to stop your property being stolen -
I cant seem to escape engineer mode as I have two line faults I cant clear or disable.
Line Fail (1) is the fault and I think Line Fail (4) is the other one.
Also (on my classic it used to say something like Manager Reset Required) now its saying "Call Alarm Co. Quote Code xxxxx".
I think you might need to get hold of a manual as the 520 is a different panel than a classic, and if you cant clear the above which is simple programming then you wont get very far as thats very basic.
-
If your trade plug your laptop in speak to cop who will tell you what software to download so they can set it up for you.
Ports 80, 7050
BT hub general dont show them in the network map, look for the MAC code instead
-
I go along with that Admin, but you would appreciate were I called to a site with these problems my first priority would be to establish when, and if, this control panel worked properly..I'm afraid I must stand by that way of working.
Nothing wrong with that
-
Honeywell need to develop it more
In what way ?
can do anything with galaxy if you know the panel
-
How do you definitely and without doubt know that it is a panel fault... anybody ? DWdave have you checked the panel (see earlier post) ?
Could be due to the fact that he has checked the fuse's and the panel doesn't stay on when the mains is removed.
Not a panel fault more the smart rio inside the 500
-
I think you have badly designed your system, using rios to reduce runs only makes sense and saves money if you have 8 circuits that are 100m away from the panel.
A GD48 would have give you 16zones onboard and 4 rios and the software on the panel is more suited to a home then a 500/520 which are aimed more at high security installations that need other things.
-
how many circuits do you have on this system?
-
if its a 500 check the ribbon cable from psu to main board.
If I change the panel, where would I get galaxy gold or dimensions equivalent from.
Galaxy D 520 is the equivalent to a 500, you will need a small fortune to replace, how many circuits you using ? a GD48 will probably do
-
either a on board fuse / wired up wrong or thats why the panel was sold on ebay, its faulty
-
Yet it worked fine on 9600 for a few weeks.
It struggled......
-
Galguy : Ive never programmed and I dont know what SIA3 or TTL is.
TTL is very basic electronics abbreviations
For now though, I think that the RS232 board has had it
I doubt it, probally a setting and they only like 1200 baud
-
Galaxy app will but unsure about a 500
-
...and then it dropped.
Check settings baud rate etc, dip switches on dump box
-
Honeywell sc100 is the proper way
-
any galaxy panel wont do inertia monitoring you need a separate analyzer
only panels that have this builtin are Aritech, HKC
-
Whats the maximum number of wireless devices on a Ricochet system ?
Anywhere near 120 devices?
-
Yeah I'm all over the Wd's and CIE's. Sometimes I like to throw in some ABC's and mix it with a little 123.
But .... I am planning to mount the extension speaker downstairs - probably the furthest point from the panel, and right above a PA trigger.
If you talking standards, the extension speaker must be heard though out the entry / exit route
-
Used these years ago, anyone tried them recently? http://www.thecrowgroup.com/Products_Systems/NEO_LINE/NEO_LINE/
-
Will ask in the morning about 7450s we had some stock put away, not sure how many are left.
-
can you use others?
No
you dont have to use it if your on local or have a fixed ip
I have explained that to the customer. local its fine but he wants to let people in from his iphone at work
-
As Pete comelite, the only thing that lets it down is their DDNS server
-
, enter the engineer code, then press reset and it should be job done
)He doesnt know it
Buying stolen property to stop your property being stolen 
)
Panel Swap - Classic 500 To Dimension 520C
in !!..DIY Installers..!!
Posted
Latest then. you might have to update your ethermet firmware
To unlock the panel and get all the features then panel needs the firmware flashing to a none ADT firmware
They dont need a number from the panel, the fact that it has ADT set as the banner text by default proves its theirs.