NeukSales Posted December 20, 2024 Share Posted December 20, 2024 (edited) Hi Everyone, I've just joined the group (see my Introduction for background!) and I see that this Lounge forum has a load of support questions, so here's mine! We have a bricked I-ON40H+ after a software upgrade to V7.07.01. Strictly-speaking, not 'bricked' in the sense that it's a lost cause, but this damned message means I can't commission it to the client, so it's 'bricked' IMO . I know the language update has to happen before a firmware upgrade, but what we think has happened here is that the engineer thought he had executed a language upgrade (all of this from a keypad) but I don't think that happened. Firmware upgrade was successful but we're left with this feckin language error message. I've did several full power cycles, danced a jig and everything else, but to no avail. My question is, is this worth saving or do we ditch it, learn a few lessons and move on; we've already spent significant amounts of time flaffing about and with no results? Thanks. Jamie Edited December 20, 2024 by NeukSales Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47061-eaton-i-on40h-panel-language-incompatibility-message/ Share on other sites More sharing options...
al-yeti Posted December 20, 2024 Share Posted December 20, 2024 1 hour ago, NeukSales said: Hi Everyone, I've just joined the group (see my Introduction for background!) and I see that this Lounge forum has a load of support questions, so here's mine! We have a bricked I-ON40H+ after a software upgrade to V7.07.01. Strictly-speaking, not 'bricked' in the sense that it's a lost cause, but this damned message means I can't commission it to the client, so it's 'bricked' IMO . I know the language update has to happen before a firmware upgrade, but what we think has happened here is that the engineer thought he had executed a language upgrade (all of this from a keypad) but I don't think that happened. Firmware upgrade was successful but we're left with this feckin language error message. I've did several full power cycles, danced a jig and everything else, but to no avail. My question is, is this worth saving or do we ditch it, learn a few lessons and move on; we've already spent significant amounts of time flaffing about and with no results? Thanks. Jamie What did technical support say ? Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47061-eaton-i-on40h-panel-language-incompatibility-message/#findComment-527030 Share on other sites More sharing options...
NeukSales Posted December 20, 2024 Author Share Posted December 20, 2024 Support advised on a power cycle. Thanks for your response. Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47061-eaton-i-on40h-panel-language-incompatibility-message/#findComment-527031 Share on other sites More sharing options...
james.wilson Posted December 20, 2024 Share Posted December 20, 2024 Don't know the panel but I'd attempt to save it. securitywarehouse Security Supplies from Security Warehouse Trade Members please contact us for your TSI vetted trade discount. Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47061-eaton-i-on40h-panel-language-incompatibility-message/#findComment-527034 Share on other sites More sharing options...
MrHappy Posted December 20, 2024 Share Posted December 20, 2024 I'd rip it out & stamp on it to ensure its dead.... If you need to replace with same thing its probably cheaper as a kit / Mr Veritas God Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47061-eaton-i-on40h-panel-language-incompatibility-message/#findComment-527036 Share on other sites More sharing options...
al-yeti Posted December 21, 2024 Share Posted December 21, 2024 14 hours ago, NeukSales said: Support advised on a power cycle. Thanks for your response. Nothing else? If you registered with them they will repair it if you send it to them ,they can probably write to it Although they might not do much ..... Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47061-eaton-i-on40h-panel-language-incompatibility-message/#findComment-527046 Share on other sites More sharing options...
NeukSales Posted December 21, 2024 Author Share Posted December 21, 2024 Thanks for that. This panel was already in situ with a client where we were carrying out a load of other work and I recommended the addition of several zones on the site. One of our guys was very familiar with this panel (duh!), so we did the biz; two radio PIRs, test, commission and it all worked like a dream - seriously, that is a top notch panel. Quite rightly, the decision was made to bring it up to the latest S/W (we do this on everything else, including NVR's, cameras, IoT, etc) to 7.07.01. We are where we are, and the client thinks the panel is around 6 yrs old but can't be sure. I've left it totally power-disconnected over the weekend, but I don't think that will change anything come Monday. Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47061-eaton-i-on40h-panel-language-incompatibility-message/#findComment-527048 Share on other sites More sharing options...
al-yeti Posted December 21, 2024 Share Posted December 21, 2024 24 minutes ago, NeukSales said: Thanks for that. This panel was already in situ with a client where we were carrying out a load of other work and I recommended the addition of several zones on the site. One of our guys was very familiar with this panel (duh!), so we did the biz; two radio PIRs, test, commission and it all worked like a dream - seriously, that is a top notch panel. Quite rightly, the decision was made to bring it up to the latest S/W (we do this on everything else, including NVR's, cameras, IoT, etc) to 7.07.01. We are where we are, and the client thinks the panel is around 6 yrs old but can't be sure. I've left it totally power-disconnected over the weekend, but I don't think that will change anything come Monday. Yeah but this is all side issue and your talking about a small install Take the board out put one of your spare ones in and reprogrammed it End of story with customer Go get an rma from support send board in for repair or swap , they may even have spare board they will swap with you But I guess I am basing my support experience with hkc who are very helpful for installers Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47061-eaton-i-on40h-panel-language-incompatibility-message/#findComment-527049 Share on other sites More sharing options...
NeukSales Posted December 21, 2024 Author Share Posted December 21, 2024 Thanks for the reply. Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47061-eaton-i-on40h-panel-language-incompatibility-message/#findComment-527051 Share on other sites More sharing options...
PeterJames Posted December 21, 2024 Share Posted December 21, 2024 18 hours ago, NeukSales said: Support advised on a power cycle. Thanks for your response. Id try a power cycle Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47061-eaton-i-on40h-panel-language-incompatibility-message/#findComment-527053 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now