sixwheeledbeast Posted August 9, 2019 Share Posted August 9, 2019 3K3 doesn't support multiple devices on one zone would need to be double pole or 4K7/2K2 Link to comment https://www.thesecurityinstaller.co.uk/community/topic/43021-texecom-old-premierveritas/page/3/#findComment-487457 Share on other sites More sharing options...
Shadrack Posted August 9, 2019 Author Share Posted August 9, 2019 the multimeter shows reed 1 at 3.3k and reed 2 on 5.2k. so I'd have to up the reed1 resistor? Link to comment https://www.thesecurityinstaller.co.uk/community/topic/43021-texecom-old-premierveritas/page/3/#findComment-487458 Share on other sites More sharing options...
sixwheeledbeast Posted August 9, 2019 Share Posted August 9, 2019 It appears the international series has allsorts of weird SEOL configurations look in the manual for wiring zones take note of the parallel "zone doubled" config you have to apply this to each circuit you wire this way. If you have moved zones around in the panel this will be setup incorrectly. Link to comment https://www.thesecurityinstaller.co.uk/community/topic/43021-texecom-old-premierveritas/page/3/#findComment-487459 Share on other sites More sharing options...
Shadrack Posted August 9, 2019 Author Share Posted August 9, 2019 I removed all sensors. I've added resistors to all zones (please check the pics if this is right?) and reset to default. I've programmed date and time. This is what I've got now: Link to comment https://www.thesecurityinstaller.co.uk/community/topic/43021-texecom-old-premierveritas/page/3/#findComment-487460 Share on other sites More sharing options...
sixwheeledbeast Posted August 9, 2019 Share Posted August 9, 2019 99 to leave engineers? If so all zones and tamper is active Link to comment https://www.thesecurityinstaller.co.uk/community/topic/43021-texecom-old-premierveritas/page/3/#findComment-487461 Share on other sites More sharing options...
Shadrack Posted August 9, 2019 Author Share Posted August 9, 2019 that is out of engineers. Engineers has all 8 lit up. I tried tamper disable pin on the controller, (has a 3 jumper pinout for Tamper Disable), same thing. Link to comment https://www.thesecurityinstaller.co.uk/community/topic/43021-texecom-old-premierveritas/page/3/#findComment-487462 Share on other sites More sharing options...
al-yeti Posted August 9, 2019 Share Posted August 9, 2019 21 minutes ago, Shadrack said: that is out of engineers. Engineers has all 8 lit up. I tried tamper disable pin on the controller, (has a 3 jumper pinout for Tamper Disable), same thing. So if you disable tampers , then might be as Swb says the seol config and resistor combination? Link to comment https://www.thesecurityinstaller.co.uk/community/topic/43021-texecom-old-premierveritas/page/3/#findComment-487463 Share on other sites More sharing options...
Shadrack Posted August 9, 2019 Author Share Posted August 9, 2019 Well I did nuke config back to defaults so it shouldn't be an issue? also I removed the broken reed and removed the wires so no more 2 reeds on 1 zone. as it is while I type this, all sensors removed, replaced with resistors. Link to comment https://www.thesecurityinstaller.co.uk/community/topic/43021-texecom-old-premierveritas/page/3/#findComment-487464 Share on other sites More sharing options...
sixwheeledbeast Posted August 9, 2019 Share Posted August 9, 2019 May not be setup for resistors as default Link to comment https://www.thesecurityinstaller.co.uk/community/topic/43021-texecom-old-premierveritas/page/3/#findComment-487465 Share on other sites More sharing options...
al-yeti Posted August 9, 2019 Share Posted August 9, 2019 8 minutes ago, Shadrack said: Well I did nuke config back to defaults so it shouldn't be an issue? also I removed the broken reed and removed the wires so no more 2 reeds on 1 zone. as it is while I type this, all sensors removed, replaced with resistors. Put wire links instead of resistors and see if anything changes Link to comment https://www.thesecurityinstaller.co.uk/community/topic/43021-texecom-old-premierveritas/page/3/#findComment-487466 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now