al-yeti Posted August 12, 2023 Share Posted August 12, 2023 8 hours ago, MrHappy said: there's ya problem.... I'd assume the fuse on the I/O is unmonitored ? you checked it ?? Enforcer will power the master blaster? Quote Link to comment Share on other sites More sharing options...
Bad-Yeti Posted August 12, 2023 Author Share Posted August 12, 2023 36 minutes ago, al-yeti said: Enforcer will power the master blaster? No, the Master Blaster is powered by a separate 240v feed the siren out is just the relay switch for the blaster. Hail be to the Yeti's Quote Link to comment Share on other sites More sharing options...
james.wilson Posted August 13, 2023 Share Posted August 13, 2023 5 hours ago, Bad-Yeti said: Aye I guess. So are Pyronix alarms not exactly great? What are a good make? Anything apart from pyronix and risco Quote securitywarehouse Security Supplies from Security Warehouse Trade Members please contact us for your TSI vetted trade discount. Link to comment Share on other sites More sharing options...
Bad-Yeti Posted August 13, 2023 Author Share Posted August 13, 2023 23 hours ago, MrHappy said: If as has been suggested, I disconnect the battery and do a I guess hard restart will it lose all its settings? Quote Link to comment Share on other sites More sharing options...
MrHappy Posted August 13, 2023 Share Posted August 13, 2023 17 hours ago, Bad-Yeti said: So are Pyronix alarms not exactly great? Fitted correctly they are bullet proof. 1 hour ago, Bad-Yeti said: If as has been suggested, I disconnect the battery and do a I guess hard restart will it lose all its settings? If you wish to default use setting - "CLEAN START" from the engineering menu However, lets start with the very basics ? Loosen the 2 screen under the panels back plate so you can hang the front panel underneath. Is the ribbon from l/O pcd fitted correctly? Have you +12v & com on DC voltage with multi meter ? Remove the trigger for MB or EWD & touch it to com your device should sound? Yes = programming issue(s) No= fuse of wiring issues Quote Mr Veritas God Link to comment Share on other sites More sharing options...
Bad-Yeti Posted August 13, 2023 Author Share Posted August 13, 2023 (edited) Ok I've discovered the problem there was a short and it had taken out one of the fuses after all is there any way to arm the system as I don't have any fuses and can't get any more until tomorrow. Is it possible to on the system with that fault? I note your comment Mr happy and you don't need to worry I shouldn't be doing any more alarms to be honest with you I didn't even want to do this one in the first place lol. Edited August 13, 2023 by Bad-Yeti Quote Link to comment Share on other sites More sharing options...
Bad-Yeti Posted August 13, 2023 Author Share Posted August 13, 2023 Okay, when I tested the siren the output from the I/o is only 2.38 volts for this sound up and 1.85 for the stroke that's with both fuses replaced Quote Link to comment Share on other sites More sharing options...
MrHappy Posted August 14, 2023 Share Posted August 14, 2023 On 13/08/2023 at 14:07, Bad-Yeti said: Okay, when I tested the siren the output from the I/o is only 2.38 volts for this sound up and 1.85 for the stroke that's with both fuses replaced between output & 12v ? Quote Mr Veritas God Link to comment Share on other sites More sharing options...
Bad-Yeti Posted August 14, 2023 Author Share Posted August 14, 2023 Got it all sorted. Looks like all the advice I got from the supplier was wrong. That the Siren and Strobe are negative switches against the 12v not positive against the common, it damaged the I/O board. Quote Link to comment Share on other sites More sharing options...
al-yeti Posted August 14, 2023 Share Posted August 14, 2023 54 minutes ago, Bad-Yeti said: Got it all sorted. Looks like all the advice I got from the supplier was wrong. That the Siren and Strobe are negative switches against the 12v not positive against the common, it damaged the I/O board. Manual would have been better to use Board is cheap and available Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.