Sanj Posted April 22, 2017 Share Posted April 22, 2017 Hi All I installed a Pyronix Sterling 10, 15yrs ago, which has been a great piece kit however the key pad is on it's way out. I've done a little research and not been able to source a new keypad (not sure I want to get a used pad). I am after some advice on what are what you guys would suggest as good replacement, I also want to add some remote monitoring to allow me to set/reset etc... Current setup (all wired): 8 x PIR 6 x Zones 1 x Panic Button 1 x Siren 1 x LCD Keypad If you need additional information to support, just let me know. All help is appreciated, It'll be good to make an informed decision based on the collective experience. Thanks in advance Sanj Quote Link to comment Share on other sites More sharing options...
aissecur Posted April 22, 2017 Share Posted April 22, 2017 euromini or texecom elite would be my choice Quote Link to comment Share on other sites More sharing options...
GalaxyGuy Posted April 22, 2017 Share Posted April 22, 2017 Galaxy G2-12, MK7 Keyprox, new 12v 7ah Yuasa battery and LCE module will be the cheapest hard wired IP panel at under £150. Wire 1 zone per sensor. Quote Link to comment Share on other sites More sharing options...
PeterJames Posted April 22, 2017 Share Posted April 22, 2017 If you think the Sterling 10 was a great piece of kit you will be amazed by anything not branded Pyronix. 1 Quote Link to comment Share on other sites More sharing options...
norman Posted April 22, 2017 Share Posted April 22, 2017 If it's served him well for 15yrs I'd say that it is (putting aside my personal thoughts on Pyronix) brother in law had a Pyronix panel in his house for c20 yrs up to moving, again that's done it's job imo. I'd look at the Texecom range btw. Quote Nothing is foolproof to a sufficiently talented fool. Link to comment Share on other sites More sharing options...
PeterJames Posted April 22, 2017 Share Posted April 22, 2017 1 hour ago, norman said: If it's served him well for 15yrs I'd say that it is (putting aside my personal thoughts on Pyronix) brother in law had a Pyronix panel in his house for c20 yrs up to moving, again that's done it's job imo. I'd look at the Texecom range btw. Just saying compared to the Sterling 10 everything else is a breeze to program use generally maintain, or even just come out of engineers mode 1 Quote Link to comment Share on other sites More sharing options...
al-yeti Posted April 22, 2017 Share Posted April 22, 2017 1 hour ago, PeterJames said: Just saying compared to the Sterling 10 everything else is a breeze to program use generally maintain, or even just come out of engineers mode Fully loaded top of range texecom should be a breeze then Quote Link to comment Share on other sites More sharing options...
norman Posted April 22, 2017 Share Posted April 22, 2017 4 hours ago, PeterJames said: Just saying compared to the Sterling 10 everything else is a breeze to program use generally maintain, or even just come out of engineers mode End users don't care about 2 of those 3 and the third they get used to. iirc to set the brother in laws you pressed 2 buttons, (running man and 1 or 0) doesn't get much easier than that. Quote Nothing is foolproof to a sufficiently talented fool. Link to comment Share on other sites More sharing options...
PeterJames Posted April 22, 2017 Share Posted April 22, 2017 1 hour ago, norman said: End users don't care about 2 of those 3 and the third they get used to. iirc to set the brother in laws you pressed 2 buttons, (running man and 1 or 0) doesn't get much easier than that. The diyers do though Quote Link to comment Share on other sites More sharing options...
Sanj Posted April 23, 2017 Author Share Posted April 23, 2017 Thanks guys for the quick response, I'll do some more research and may come back for more advice no doubt later on. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.