-
Posts
190 -
Joined
-
Last visited
-
Days Won
2
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by lymebayalarms
-
-
Hi,
PM me further information.
-
Howdo,
Been a while since I have frequented these pages...have I missed much?!
I am looking for work overseas, either EU (not getting into the whole debate!) or further afield ideally contract. Any recommendations for sites/agencies to visit?
Anyone had any experiences good or bad?? Feel free to share!
Thank you people!
-
Opener...
-
-
23 minutes ago, datadiffusion said:
In that case Clik would be OK but again the real benefit is if you are using Sage for accounting as it fully integrates, if not, you might just as well save your money and run some sort of manual system imho.
Think Clik now works with Xero now.
-
7 hours ago, Nogger said:
I don't use all the functionality of AM I just need to schedule service and maintain contract details and correspondence and interact with field engineers.
Clik would tick the boxes then.
-
2 hours ago, Jim Randle said:
Hi , I'd default the panel and start again. Don't bother with two areas or Area Arm Suites. Everything in area A. Landing Part 1 Omit. Keypad Quickset on. Hall Guard Access. Part Arm Silent. What can go wrong? Press Part then yes at night. Landing will be off, Hall will be Entry. Jim
Second that.
No point complicating things as previous.
- 1
-
-
Have you checked the UDL password is correct
-
Personally, I have now stopped doing any Fire with a sleeping risk now... rarely find a compliant install and have found most owners are looking at the bottom line for compliance.
Seen some real gash over the last few year, 1 zone covering 9 flats on 4 floors to no services for 12 years plus... work on the opinion now that if the owner has that little respect for fire safety I am not interested.
So, on that cheery note... Dont quote it with out a walk around of each site, open some panels have a look at whats what, check the paperwork on site to see what order its in....cover you **** or risk getting it ****** when you drop the soap!
-
Its defined by the FRA.
-
Residential Home - Higher Risk? If so I would say stick to quarterly if it has been defined by a FRA.
Do you have much experience with fire?
-
6 hours ago, datadiffusion said:
Other old lags may laugh, but despite the fact we use Siemens DTs, Elmdene flush contacts, insist in copper cable, when it comes to speaker we use...
...Lynteck
http://www.lynteck.co.uk/products/intruder/sounders/LY07-009-37.php
They are very flat, large enough to cover old sounder holes (with plenty of screw holes) and because they are so small, the actual
speaker element is the sort of 'potted' type you get in a mobile phone, with a thick black cone and much better than the usual mylar ones.
Customers like them as they don't look like something from a cold war era Gardiner catalogue and best of all are matte so take paint well...
Tidy looking unit, what's the cost roughly?
-
Missing Kiss of, prob due to poor line condition or installer has set the system up incorrectly. Dues it happen on every signal?
-
Remove the trigger for the hardwired. Delete the other bell and relearn when the testing is complete.
- 1
-
I guess you will be changing yours straight away.... #allthingsmedical
-
-
I would offer to fit it for free to a wheelie bin of their choosing...
-
1 hour ago, norman said:
180 days, wow I need to remember that one and I thought Amazon Prime were **** hot for the seller...
Perhaps ADI should take a leaf from their book!
-
5 minutes ago, sixwheeledbeast said:
I am not sure why you can't do that.
You can assign as many attribute 1's as you need.
It would be useless if you couldn't use Omittable/Part 1,2,3/Access/EE2 or Part Guard simultaneously
Agreed, although I normally program via wintex so it's a tick box option
- 1
-
2 hours ago, 1animal1 said:
But can you omit two zones from both part sets? And if so, where would you do this?
Each zone, under attributes "omit part 1 and omit part 2" will only then be active on full set.
-
Okay sometimes the metal doors will screw with the magnetic fields of the magnet. If you get issues cut a bit of plastic or rubber to sit between the magnet and the door. If you cut it to the same shape as the magnet you should hardly see it, esp if it's white.
- 1
-
2 minutes ago, 1animal1 said:
These impaq-w door contacts are fun fitting on upvc doors with curved edges... The lip on the magnet is ever so slightly out to fit under the rubber
I always bin the magnet they come with, fit a proper one from a surface door contact. Looks neater too imho
- 1
-
If you don't know the code, call in the Pro's
On call out and rest time
in General Security & Fire Queries
Posted
Clear 11 hours rest before starting work the next day.