WDT Posted August 30, 2015 Share Posted August 30, 2015 Yep Is the keypad near to either door as there are two zone inputs on the keypad that you could use for either front or rear door that would then give you ten zones i.e Zone 1 on keypad door contact Zone 2 on keypad vibration circuit Link to comment https://www.thesecurityinstaller.co.uk/community/topic/39020-texecom-premier-install-trouble/page/3/#findComment-428834 Share on other sites More sharing options...
BveshPatel Posted August 30, 2015 Author Share Posted August 30, 2015 Interesting point, unfortunately they keypad is outside the area of the control panel due to requirements. Can I wire the shock in series? Link to comment https://www.thesecurityinstaller.co.uk/community/topic/39020-texecom-premier-install-trouble/page/3/#findComment-428841 Share on other sites More sharing options...
charlie6 Posted August 30, 2015 Share Posted August 30, 2015 Alyeti:- "To much info," I believe I am in a better position than yourself as regards the amount of 'info' in a reply..as you are well aware !!! Link to comment https://www.thesecurityinstaller.co.uk/community/topic/39020-texecom-premier-install-trouble/page/3/#findComment-428842 Share on other sites More sharing options...
WDT Posted August 30, 2015 Share Posted August 30, 2015 What about a on board expander theres a plug on version that adds 8 zones or there is a 4 zone one that uses up 2 keypad address's I would go for the 8 zone out of choice in case of future upgrades Link to comment https://www.thesecurityinstaller.co.uk/community/topic/39020-texecom-premier-install-trouble/page/3/#findComment-428846 Share on other sites More sharing options...
WDT Posted August 30, 2015 Share Posted August 30, 2015 WDT:- "...I don't know if to laugh or cry on the 12 core subject..." Well Alyeti has been proved 'wrong', he has admitted that he is wrong, he accepted that he was wrong...but he still keeps on in the belief that he is not wrong on that topic..I find that absolutely amazing !!! No more Link to comment https://www.thesecurityinstaller.co.uk/community/topic/39020-texecom-premier-install-trouble/page/3/#findComment-428849 Share on other sites More sharing options...
BveshPatel Posted August 30, 2015 Author Share Posted August 30, 2015 Tomorrow is bank hol so not sure where I would get an expander from. Also what happens if I did wire into the same Zone? Link to comment https://www.thesecurityinstaller.co.uk/community/topic/39020-texecom-premier-install-trouble/page/3/#findComment-428851 Share on other sites More sharing options...
WDT Posted August 30, 2015 Share Posted August 30, 2015 You would not know which one tripped the alarm which makes its hardder fault finding You would have to wire them in series Link to comment https://www.thesecurityinstaller.co.uk/community/topic/39020-texecom-premier-install-trouble/page/3/#findComment-428853 Share on other sites More sharing options...
BveshPatel Posted August 30, 2015 Author Share Posted August 30, 2015 Ahh……ok So I guess the only option is to wire them In series in which case would this be correct Reed to Reed 4k7 Tamper to Reed 2k2 Tamper to control Panel Reed to control panel Alarm to Alarm 4k7 Alarm to control Panel Link to comment https://www.thesecurityinstaller.co.uk/community/topic/39020-texecom-premier-install-trouble/page/3/#findComment-428861 Share on other sites More sharing options...
WDT Posted August 30, 2015 Share Posted August 30, 2015 It can be done very easy with no resistors. With resistors you need to have the 2k2 one in line. I would get the rest working first and then sort the vibration out and add them in later after you have the expander Link to comment https://www.thesecurityinstaller.co.uk/community/topic/39020-texecom-premier-install-trouble/page/3/#findComment-428868 Share on other sites More sharing options...
BveshPatel Posted August 30, 2015 Author Share Posted August 30, 2015 Sorry for the late reply, but I am beginning to see my confusion slightly, would it be safe to say that as per one your earlier posts that and your most recent one that in order for me to get the Door contact working I should wire as follows: Reed to Reed 4k7 Tamper to Reed 2k2 Blue from Reed to Z1 on panel Yellow from Tamper to Z1 on Panel. Therefore leaving alarm terminals unconnected for the moment as this relates to the vibration? Link to comment https://www.thesecurityinstaller.co.uk/community/topic/39020-texecom-premier-install-trouble/page/3/#findComment-428935 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now