HoofHearted Posted May 8, 2009 Share Posted May 8, 2009 I've fitted my own alarm system and i'm very happy with it. The panel is a Bosh Abacus Evolution. The sounder is a Texecom Odyssey. This is completely non-standard, but so I can tinker without disturbing my neighbors, I've installed a secret switch inside the house and taken a seperate wire from the sounder to this switch. This wire breaks into the connection to one side of the siren. I was surprised to find that when the switch is in the off position, the siren still sounds at about 25% of the normal volume. So I assume that this must be caused by inductance along the wire. To make sure, I disconnected the switch altogether and got the same behavior. ie at the switch end, the ends of the wires were not connected to anything. Can anyone suggest anything that I can connect into the circuit in order to stop this happening? Thanks in advance? Ian Link to comment Share on other sites More sharing options...
FASTCAR Posted May 8, 2009 Share Posted May 8, 2009 I can't help with that particular problem , but the Texecom sounders have an engineer function , that can be invoked when doing maintenance / tinkering. Link to comment Share on other sites More sharing options...
HoofHearted Posted May 8, 2009 Author Share Posted May 8, 2009 I can't help with that particular problem , but the Texecom sounders have an engineer function , that can be invoked when doing maintenance / tinkering. That sounds useful. How do I invoke this? Link to comment Share on other sites More sharing options...
FASTCAR Posted May 8, 2009 Share Posted May 8, 2009 Its in the manual that comes with the sounder , and also in most of the Texecom Alarm Installation manuals. Link to comment Share on other sites More sharing options...
Amps Posted May 8, 2009 Share Posted May 8, 2009 I've fitted my own alarm system and i'm very happy with it. The panel is a Bosh Abacus Evolution. The sounder is a Texecom Odyssey.This is completely non-standard, but so I can tinker without disturbing my neighbors, I've installed a secret switch inside the house and taken a seperate wire from the sounder to this switch. This wire breaks into the connection to one side of the siren. I was surprised to find that when the switch is in the off position, the siren still sounds at about 25% of the normal volume. So I assume that this must be caused by inductance along the wire. To make sure, I disconnected the switch altogether and got the same behavior. ie at the switch end, the ends of the wires were not connected to anything. Can anyone suggest anything that I can connect into the circuit in order to stop this happening? Thanks in advance? Ian so the wire to the siren in the bell box is in series with the switch? the switch goes open and the siren still works at 25%? possibly there two sirens in the bell box and you have only connected one through your switch? Link to comment Share on other sites More sharing options...
antinode Posted May 8, 2009 Share Posted May 8, 2009 You need to use a double pole switch then to break both connections to the sounder, although I don't recommend fitting anything that will intentionally prevent a sounder from working like that. Trade Member Link to comment Share on other sites More sharing options...
james.wilson Posted May 8, 2009 Share Posted May 8, 2009 id be vary cautious here as it sounds like you have broke into the piezo wire. if so there is a lot of voltage going to those 10-20000v if i recall same as a strobe. also if someone removes your sounder from the wall it wont sound securitywarehouse Security Supplies from Security Warehouse Trade Members please contact us for your TSI vetted trade discount. Link to comment Share on other sites More sharing options...
Guest old-hand Posted May 8, 2009 Share Posted May 8, 2009 Back to the manual then and use the engineers hold off facility. Link to comment Share on other sites More sharing options...
HoofHearted Posted May 8, 2009 Author Share Posted May 8, 2009 Back to the manual then and use the engineers hold off facility. I've been digging around. I cant find the documentation that came with the sounder. I had a look on the web and although I found some documentation, it didn't explain about the engineer mode in a way that I could understand. Link to comment Share on other sites More sharing options...
Guest old-hand Posted May 8, 2009 Share Posted May 8, 2009 Sorry we cannot tell you how to do this in the public area, see the site rules. Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.