Hugh94 Posted September 30 Author Share Posted September 30 2 hours ago, MrHappy said: I'd assume the spark may have tested a new spur with your controls attached I have spare psu's, I did have issues some years ago, they go funny before failing... The logs show 1 mains fail & loads of tampers & supervision faults ? Is the sub seeing unreset faults when they put their code in for another tamper or supervision fault? What's the max time I can set for the AC Delay? Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47380-pyronix-enforcer-v10-mains-fail-fault/page/3/#findComment-530912 Share on other sites More sharing options...
MrHappy Posted September 30 Share Posted September 30 21 minutes ago, Hugh94 said: What's the max time I can set for the AC Delay? 250 minutes ? Mr Veritas God Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47380-pyronix-enforcer-v10-mains-fail-fault/page/3/#findComment-530913 Share on other sites More sharing options...
PeterJames Posted September 30 Share Posted September 30 2 hours ago, Hugh94 said: 1, goes from a spur to a built in step down/PSU to 13-15v, checked voltage on it and gives out correct voltage What about current draw? As Happy mentions are the devices (inc bells) connected wireless Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47380-pyronix-enforcer-v10-mains-fail-fault/page/3/#findComment-530914 Share on other sites More sharing options...
Hugh94 Posted October 1 Author Share Posted October 1 3 hours ago, PeterJames said: What about current draw? As Happy mentions are the devices (inc bells) connected wireless 3 hours ago, PeterJames said: What about current draw? As Happy mentions are the devices (inc bells) connected wireless Here's what the panel sees, I still need to find the time to get out and check the supply myself again after the new spur has been installed Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47380-pyronix-enforcer-v10-mains-fail-fault/page/3/#findComment-530916 Share on other sites More sharing options...
Hugh94 Posted October 1 Author Share Posted October 1 8 hours ago, MrHappy said: I'd assume the spark may have tested a new spur with your controls attached I have spare psu's, I did have issues some years ago, they go funny before failing... The logs show 1 mains fail & loads of tampers & supervision faults ? Is the sub seeing unreset faults when they put their code in for another tamper or supervision fault? So supervision faults pop up here and there like the bell and the farthest away pir but then clear again, I changed the timer to 250 and reset but still not staying clear, the current is 0.0A, see picture attached for details Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47380-pyronix-enforcer-v10-mains-fail-fault/page/3/#findComment-530917 Share on other sites More sharing options...
MrHappy Posted October 5 Share Posted October 5 Hugh, I'm going with 1 x Plaggy enforcer controls & NOTHING as wired devices on the system ? Supervision fault, what's the signal strength of each radio device on the system ? Are all batteries 2yrs old or less, when they are replace spin them around in the holder to ensure there are go contacts If the house is not 'kin massive & the controls are no in silly place eg in cupboard surrounded by display cases of lead painted figures or something Swap the device far away for an identical item which works fine in a different location, ideally the item which drops of in location A should drop on in location B, proving the device is duff... chances are all the hardware is fine & its an issue with the environment of the installation ? Mr Veritas God Link to comment https://www.thesecurityinstaller.co.uk/community/topic/47380-pyronix-enforcer-v10-mains-fail-fault/page/3/#findComment-530923 Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now