-
Posts
106 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by James R
-
-
Hi all
Got a Gardtec panel that has 2 panic alarm wireless fobs as zones 92 and 93
When customer started setting procedure - alarm wouldn't set and got a alert message on one of the panic fobs - wouldn't reset with engineers code and kept into 'alert! Enter code' or something to that effect. It leads me to think the panel thinks the fob is being pressed due to a fault and won't set as a result - all the alarm reset codes are either 'any code' or 'engineers code' so I don't think there's a different code that I don't know for PA reset. Wondered if any one has had similar issues? Or have any info
Regards
-
30 minutes ago, The Arab said:
I would have thought you'd do the first detector as entry, then time set would be enough time to allow the detector to settle say 30 seconds then it depends how far keypad/prox is from the detector so say 20-30 seconds
Sorry yes first dt is set to entry (exit is the one to be used with a push button?)
Yeah, think 30 secs for the timer on setting - kp is in the entrance lobby and the dt is in the lobby set to ENTRY.
-
18 minutes ago, sixwheeledbeast said:
It's the wiring regs, covers any wiring up to LV.
I don't think they aim to be vague they aim to be concise and clear.
One issue I do have is all these standards are set for good practices and safety reasons, cost decent money to buy but they refer to so many other regs in each other you would be bankrupt if you bought everyone that is referenced.
I refer to regs only to follow the changes-- the big ones recently being fire resistant fixings for all surface mtd cabling in or out of non metal containment in commercial installs, afdds which I still don't fully get.
There's some car charger stuff. Would you use lsf b/a cable on a commercial install even if not specced?
-
I am waiting to be vetted, hoping it won't take too long.
-
Hi all,
Have a galaxy install where no door contacts have been specced - so unable to start setting/unsetting from a zone - set the dt pir at the front door lobby to EXIT and was wondering how best to set up the system for the customer - with timers for setting/unsetting?
Regards
-
Are All unused zones set to 'not used' in zone programming?
-
6 hours ago, sixwheeledbeast said:
As I understand it they are moving towards cabling being at least LSZH and not allowing plastic containment to be used in the next amendment of BS7671.
Not only due to failing of containment/fixings during a fire but due to toxic fumes and poor vision when trying to escape. I mention this for those using YT2 galv support clips.
I think there is still room for innovation in fire proof fixings for all surfaces, unfortunately cheapest options always win.
Never used low smoke b/a cable. We would go low smoke for all other cables in commercial installs t+e, flexes etc.. . I suppose bs7671 covers elv systems or does it? Those regs can be very vague.
Like the look of those fire clips where you just drill a hole and hit em In.
-
18 hours ago, GalaxyGuy said:
If port forwarding for use with the GX app, you can only lock down the RSS and UMS passwords with RSS at the moment. In saying that, the best advice is to use a VPN rather than opening ports up.
They also specced a gsm/gprs comms module - we are setting up radio/radio Dualcom for keyholder monitoring, I take it there's no need for the honeywell module as well?
-
18 hours ago, GalaxyGuy said:
If port forwarding for use with the GX app, you can only lock down the RSS and UMS passwords with RSS at the moment. In saying that, the best advice is to use a VPN rather than opening ports up.
Hi, dont have the RSS. Can't justify the cost as we don't do a lot of galaxy.
One question, got an ip module that's been specced - would that just connect to customers network to be able to use the app?
Regards
-
52 minutes ago, al-yeti said:
You have fitted some alarms with someone yet?
Y but Not enough mate
-
48 minutes ago, al-yeti said:
You blagging?
Cos I professional blagger and only room for.ome here
Blagging how lad?
-
1 hour ago, norman said:
How big is the system?
Panel - gprs comms module- ip comms module - 15 dt pirs... I'm thinking I'm gonna set it up and program in the office before I hand it to my installer.
-
13 minutes ago, sixwheeledbeast said:
Maybe a spit gun but not staples...
Not one of those f-ckers that make you jump on-site everytime they go off?
-
23 hours ago, James R said:
Hi all, done a few paxton10 installs and personally think it is the F-ing ******** (unless your using 3rd party cameras) anyone have any views on this system?
What's up access control installers? Am I in the wrong place or what?
-
Hi, would like to start a topic specifically for interflex installers to share info on - best/worst experiences, rough installs, hints and tips etc...
Look forward to hearing from you...
Regards
-
Hi, would like to start a topic specifically for Paxton installers to share info on - best/worst experiences, rough installs, hints and tips etc...
Look forward to hearing from you...
Regards
-
-
1 minute ago, Imnotshankled said:
I personally quite like galaxy panels you can just program via keypad instead of using the software
I will be - got a quote, about 900 quid for their remote service suit with one licence - Key pad it is then...
-
-
-
2 minutes ago, PSE said:
Very easy to use, 12mm Diameter only.
Fir a nice clean but free cut, I use a standard 15mm copper pipe cutter.. nice and neat with no jagged edgesNice... What's the prices like on that gear? Had to do a whole job (sparky) in stainless steel conduit before... Nearly died in the process lol
-
14 minutes ago, MrHappy said:
An EOL circuit is 2 wires, these have been twisted together to make pair of cables
I'd use a drill, with a hook in the chuck
The pic is not my work but that of @PSE
mine look better with the lid on
My cabling also looks like a F-ing masterpiece when the ceiling tiles are back in
-
3 minutes ago, MrHappy said:
That looks good - as a background as a sparks I would have just used 20mm galv conduit - is that stuff easier to install? Obvs galv conduit is a c*nt
-
Hi all, is there a staple gun that will fix into masonry? Electric or not- from what I've seen even the battery staple guns can't do it... Any one have any recommendations?
Regards
Risco 2 button panic alarm wireless fob issue
in Control Panels (Public)
Posted
Hi all
Got a Gardtec panel that has 2 panic alarm wireless fobs as zones 92 and 93
When customer started setting procedure - alarm wouldn't set and got a alert message on one of the panic fobs - wouldn't reset with engineers code and kept into 'alert! Enter code' or something to that effect. It leads me to think the panel thinks the fob is being pressed due to a fault and won't set as a result - all the alarm reset codes are either 'any code' or 'engineers code' so I don't think there's a different code that I don't know for PA reset. Wondered if any one has had similar issues? Or have any info
Regards