[Euro-Meridian Eur-081 Euro 44+]

Hi Team,

 

I got this box from ebay and then got the keypad from a different person again off ebay.

 

i managed to get the manual but having problems to connect the pir.

 

Can anyone advise pls.

 

I

[Euro-Meridian Eur-081 Euro 44+ 2.5 Amp G]

Hi Guys,

 

I got this box as second hand and it did not come with a manual or anything.

 

Does anyone knows exactly what model this is pls?

[Cooper Menvier 9651]

Ok well I was just trying my luck  by the way thanks to everyone for all their help  everything is working fine sure i still have some setting questions but i read the installer manual and then if needed i ask the question.

 

,

 

Raj

[Cooper Menvier 9651]

Ok, will do and report back hopefully all good news )

another thing if I may, is there a way to link this product to ethernet so you can get notification if the alarm been triggured.

[Cooper Menvier 9651]

Sorry forgot to upload the pic for the door contact.

 

The red and black should it go to the cct(number) and the yellow and blue is the tamper one correct?

 

,

 

raj

[Cooper Menvier 9651]

ok success on. pulled everything to a table and started to test. Comes out to be the spring on the tamper switch on the pir was not getting pressed properly in any of the 3 devices.  Unit going off installer mode now  )

 

 

A second question if I may, does anyone know how to install a door detector pls.

 

Here is a pic of what I have.

 

Now to what I understand the yellow and blue one is the tamper.

 

The red and black do they go to a zone or to power 12vand 0 not sure.

 

My bet, goes to a zone and I break the serial link on the tamper loop and add this one as the same in serial.

 

Am i correct?

 

,

 

Raj

[Cooper Menvier 9651]

Hi everyone thanks for all the replies.

 

I have got the system rewired with 8 core alarm cable.

 

Unfortunately again same zone 1 , 2 , 3 tamper .

 

I get a meter tomorrow and try again.

 

Can anyone tell me what volts should i get on the tamper loop.

 

,

 

Raj

[Cooper Menvier 9651]

so if i get the right cable and with the current wiring should it work

[Cooper Menvier 9651]

yes its cat 5

Do you think its the cat 5 cable thats the issue?

[Cooper Menvier 9651]

[Cooper Menvier 9651]

i have it on cc its option 21 then 0

 

21: Zone Configuration
This command enables you to select the wiring type of the zone connectors
on the control unit PCB. The default is option 0 for all models.
0 Up to 8 closed circuit loop zones (CC + Com A/T).
1 Up to 8 fully-supervised loop zones (FSL 2K2/4K7).

 

Is the wiring right.  I done it as it says in the book

[Cooper Menvier 9651]

I upload proper pics shortly.

 

But thats how its connected.

[Cooper Menvier 9651]

so should i disconnect the tamper from the pir and box?

[Cooper Menvier 9651]

anyone with any ideas pls

[Cooper Menvier 9651]

Its DP and the program is 03 normal alarm.

 

I did a 98 before to reset the system to default. Then disable all the rest so from zone 04 to 08.

 

,

 

Raj

[Cooper Menvier 9651]

Hi guys,

 

I am new to alarm. I recently bought a second hand cooper menvier 9651 and installed it.

 

I followed the manual and the instructins on

 

http://www.thesecurityinstaller.co.uk/community/topic/29401-cooper-menvier-9651/page-2

 

were very helpful.

 

I seem to have one issue.

 

When i put power to the system, i am unable to exit installer mode.

 

It keeps saying the zone1,2,3 tamper.

 

Can anyone help on this pls.

 

,

 

Raj