[Switching Pir To Viper Glx Shock - Wiring Advice - Galaxy G2-20]

Your mixing inputs and outputs up.

you cant use any if the 000x outputs for anything but comms equipment

 

Ok; sorry folks!

 

- Do I need to be in the panel/move any wiring?

- 1001 thru 1004 seem to be pretty much essential...? Would changing these have a detrimental affect on the operation?

 

I just need to nail this and im set...

[Switching Pir To Viper Glx Shock - Wiring Advice - Galaxy G2-20]

The 000x outputs are off the comm trigger lead so you cant use them, it will have to be one of the 100x outputs your currently not using

 

So I can change 0001 from Fire to DetRst, but I'm not sure how link that specifically to what is Zone 1004 in this case...

 

I am not entirely sure which Zone 1004 is in the panel...

 

 

Do I even need to be in the panel!?!?

[Switching Pir To Viper Glx Shock - Wiring Advice - Galaxy G2-20]

I've read the book of words and it's got me confused...

 

My outputs;

 

1001 Set

1002 SPK Driver

1003 Bell

1004 Strobe

0001 Fire

0002 Panic

0003 Intruder

0004 Assist

0005 Omit

0006 Fault

0007 Confirm

0008 Tamper

 

Is it simply a case of changing 0003 Intruder to DetRst? Would that change all my Zones set to Intruder to DetRst, and if so, is that a problem?

 

I'm guessing I cannot set a specific zone to a specific output via RKP.

 

Looking at the wiring within the panel, I am able to identify the Viper, however, cannot see how changing the wiring in there would help.

 

Help? 

[Switching Pir To Viper Glx Shock - Wiring Advice - Galaxy G2-20]

The LED was off when closed/clear, after triggering the GLX during testing, the LED is constantly flashing.

[Switching Pir To Viper Glx Shock - Wiring Advice - Galaxy G2-20]

You need to drop the power to it for a few seconds before setting, we used to fit a n/c button on the bottom of the panel or adj the rkp.

 

Is that drop power to the GLX, or panel?

 

Bit of a pain really - can I disable the LED totally, given its location it would be fairly obvious if that was the PoE?

[Switching Pir To Viper Glx Shock - Wiring Advice - Galaxy G2-20]

Finally got round to sorting this tonight, during testing all was well. But since it has triggered, the LED has not stopped flashing.

 

Arming/Disarming has not helped.

 

Anyway to sort/reset this?

[Switching Pir To Viper Glx Shock - Wiring Advice - Galaxy G2-20]

Correct me if I'm wrong, but I'm sure last time I fitted an EV-105, the neg is on the outside with the pos next to it (the link is the negative control line for the LED)

No rest time?

 

I'll look out for that.

 

Thanks for the tip with the bare wires too. This is just hooked up temp so I know what goes where whilst the room is refurbed.

[Switching Pir To Viper Glx Shock - Wiring Advice - Galaxy G2-20]

guys!

[Switching Pir To Viper Glx Shock - Wiring Advice - Galaxy G2-20]

Like this

 

CP.JPG

 

 

Excuse the CAD drawing

 

My hero

Is the shock self resetting? The older ones wernt. And used to have to fit a normally closed push button on the panel to drop the power for a second for it to reset.

 

It's a brand new Viper GLX, I don't understand the above, but am assuming I don't need to do anything funky?

[Switching Pir To Viper Glx Shock - Wiring Advice - Galaxy G2-20]

Hey all, just in the process of rejigging the alarm, and it's been a while since I've tinkered with the wired stuff...

 

I want to switch a single PIR for a Shock on my G2-20...

 

Forgetting the 'quality' of the wiring, how would this transplant over to the Viper?

 

 

 

 

And resister location??

 

Thanks in advance!