Carlos12
-
Posts
19 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by Carlos12
-
-
Would I be OK have two exit routes? I've set the neighbours door contacts set as Exit Route already
Would this allow them to have time to unset the alarm when coming down?
Thanks!
-
I've recently got an existing installation working for a neighbour, thanks so much for your previous help!
However, the only thing not working is the B setting, put code in, press B = Zone Fault 2 and the alarm makes a loud horn noise.
It's fine when it's set in A setting.
Any clues? I have Zone 2 as 'ER abcd' | Zone 2 is the PIR setting to be activated when coming down the stairs.
-
All done! THANKS SO MUCH EVERYONE!!
I annoyed the other neighbours though, forgot to set the entry and exit routes and had the alarm going full pelt twice!!
Let me know how I can repay the favour, thanks again.
-
Everything is functional apart from the door chime.
I've changed the settings on the keypad, to OFF and back ON, it makes the sound - but when the sensors move theres no sound?!
What could be the explanation for this?
I really appreciate your help, every days a school day! Thanks so much, my neighbour will be so chuffed it's fixed
-
PERFECT!! We're sorted.
Just a few more issues:
Smoke Alarm,Fault?! Zone 10
Door chime not working?
And how to do I change user codes?
I've checked instructions but unable to find any information, thanks.
-
I'll check all wiring, thanks. Only the one keypad.
-
-
4 minutes ago, sixwheeledbeast said:
Just link them all like the white lines on the PCB
Thanks so much! Will do this, obviously turning everything off first.
-
Just now, al-yeti said:
Link it or make it used or spare
Just to clarify, I'm really not used to this, I'm a wood butcher by trade haha.
Link CCT7-CCT8, the same as CCT5-CCT6?
-
2 minutes ago, sixwheeledbeast said:
Whats on Zone 8? It's likely unrelated to the bellbox being a Zone
It says "technical" on instruction manual. only 1-4 zones are used.
Technical (TC) (Key in 08). Use this zone type when you want to monitor equipment, for example a freezer, without raising a full alarm. If a technical alarm zone is activated while the system is set, the system makes no audible alarm. However, when a user unsets the system the keypad indicates a fault.If a technical alarm zone is activated while the system is unset then the system starts a pulsed tone from the keypad. If programmed, the control unit also starts communication. When a user enters a valid code the keypad stops the tone and displays the zone.
-
Wired this up, getting a fault on Zone 08?
Scroll down for bellbox wiring.
Really stumped what the issue is? Any help is really appreciated, thanks.
-
Many thanks!
-
Thanks so much everyone!!
-
I've replaced siren / sounder as stated in first post. Good heads up though.
Would this wiring combination work?
Bell box
V+ red
V - blue
Sw black
St green
R yellow -
-
-
Correct.
-
Hello,I'm helping a neighbour with an existing installation, the wires have been ripped out of the bellbox, I've connected the siren, however I'm struggling to locate the other wires.I've attached PCB wires to help conversion.Would anyone be able to assist? I've connected as best I can and I receive 'bell tamper' error however tried resetting through engineers menu and it's not working, therefore I believe it's wired wrong.Please help.From 'BELL' Feed:Black -C2Green - NC2Yellow - TRRed - 12VBlue - 0V-- Not connected:WhiteOrangeBrownImages here:Would this work?AG6 Honeywell.
Scantronic 9651 - Zone Fault - B Setting
in !!..DIY Installers..!!
Posted
Final Exit, thats the one. I replaced the battery in PCB, and problems have arisen since.
Yeah, may have to experiment. Thanks.