Sirenblinky
-
Posts
28 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by Sirenblinky
-
-
-
Thanks for the help. I went into the menu
Diagnostic
Wired devices
View input
Endstation
Shows cf
I've not been able to get to the bell box yet but unsure what is meant by short out and bypass tamper quoted . Thanks
-
Yes you have helped me with this one already I thought I had fixed it. I am thinking now the bell box is faulty. I don't think it's water ingress because when I installed it I duck taped the circuit cover and sealed the holes with silicone
-
I've installed this system over 2 months ago and over the last few days I've been getting a tamper warning bell box (Deltabell E). Both the siren and panel sounded. So I checked the Deltabell Microswitch and adjusted the back tamper screw on the bell box. All was ok for 24 hours
However this morning the panel sounded with out the external bell box sounding.
Log indicates input 33 tamper bell box with a amber fault warning on panel flashing.
To get around this I deleted input 33 and the panel warning light had gone . However this cannot be the solution to the problem. Help please.
-
Well been up the ladder lid off and no screw fitted to back of box to secure the microswitch!
My fault for not reading instructions that came with Deltabell. I wondered what the long screw was for in the accessories pack.Screw fitted this will stop the switch movement.
Must try harder in future.
-
I thought think your all right because when I put it up I did not adjust the screw on the tamper switch I thought it was making good contact with wall. I will check it when it's dry not a lover of heights and ladders
-
Can't see any evidence or this it's mounted high enough can't get to it without a ladder.
-
I've got a Deltabell E wired to a pyronix enforcer. It's been fine for 2 months then this morning the siren goes off with the log : Bell box tamper lid open at 03:28.59 seconds and at 03:29.08 seconds.12 seconds apart. No rain no wind tamper leveling screw correct and lid correct.
Could this be blip?
-
20 hours ago, al-yeti said:
DIY trigger
Ok all sorted now output not set correctly the bell should be set to siren any and bell any.
The bell output was set to engineer test or something like that.
Now working as it should
Thank you all.
-
So I might do a clean start. The go from their
-
Siren is wired worked perfectly before adding the pir. If I enter the engineer code the siren will sound then when I scroll down to log what am I looking for wording wise
-
Hi. I programmed an extra pir sensor today and I may of altered the program on my pyronix enforcer w.e. Everything is working fine however when I enter engineering mode the hard wired siren goes off. Any ideas what I've done?
-
Ok thanks it's a class 2 though I not sure what that means probably to do with home insurance.its not a light box model
-
Hi
4 hours ago, al-yeti said:I meant programming of resistance if needed
Hi thanks for responding. I think I have got the wrong resistor in the bell it's a 4k7 I will change it for a 2k2. Will having the wrong resistor connected give me the issue I am having is it that critical? Don't no anything about resistors
-
Yes set input 33 to tamper on panel and wire from T Deltabell to Z33 in panel used 2k2 resistor from T in Deltabell linked to 12v - in Deltabell
-
Good morning. I have managed to hard wire the above kit. However if I put the Deltabell in to tamper triggering the microswitch the bell sounds and strobe works but no warning is displayed on the panel. Is this normal?
-
-
I think the resistor I have in the pics is a 2k2 according to its colour bands.
-
Excellent help guys will try again this morning thanks
-
Here are some pics
-
3 hours ago, Sirenblinky said:
I tried to upload a photo but the file is to big so :
deltabell: from the top terminal
white_T
resistor_T
eng hold_ none
stb_yellow
bell_green
12v_red
negative_black also resistor into this terminal linked in to 2nd T above
Enforcer panel
Red_12v+
Black_common
Green_bell
Stb_yellow
White_D1
No links or resistors in panel
Frustrating grrr
Thanks
-
I tried to upload a photo but the file is to big so :
deltabell: from the top terminal
white_T
resistor_T
eng hold_ none
stb_yellow
bell_green
12v_red
negative_black also resistor into this terminal linked in to 2nd T above
Enforcer panel
Red_12v+
Black_common
Green_bell
Stb_yellow
White_D1
No links or resistors in panel
Frustrating grrr
Thanks
-
Hi so I got the Deltabell and tried to wire it to the Enforcer panel. The problem I have is that when I arm the panel the Deltabell goes off!
Please would someone advise me how to wire it including where the jumpers should be. I've set the jumper to SCB mode not sure about the rest. Thanks
-
Ok thanks looks like I will need an SCB box and a ladder then!
Pyronix enforcer V10 tamper input 33 bell box
in !!..DIY Installers..!!
Posted
Just wondering are you local to me. I am based in ub6.