Solomon
-
Posts
8 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by Solomon
-
-
Ok, things I've tried...
1) joined red and black at the sensor end. This allowed the alarm to set properly but, obviously, not trigger the alarm with movement.
2) joined blue and yellow at the sensor end. Immediately set off the tamper alarm. No change regarding being able to set the alarm.
3) swapped red and black st sensor. No change.
4) swapped white and green at sensor. Power to sensor stopped.
beginning to think I've damaged the sensor?
-
On 20/11/2017 at 21:37, sixwheeledbeast said:
Green and Black wires are wrong way round in the sensor if you look very closely.
It will be one beep for zone 1 active.
Pretty sure that's not the case, tbh. The black and red are together on the left, the green and white are yet two central wires. The green is very dark.
-
24 minutes ago, al-yeti said:
Lol didn't spot that , could be cos they normally have negs together in the panel end
He means you sure it's negative to negative and positive to positive
No I'm not sure
I will swap and see what happens.
-
1 hour ago, sixwheeledbeast said:
Wiring looks fine from what I can tell.
How many times is the system beeping?
Likely to be a tamper issue I agree.
Or maybe a blown fuse would make sense if the PIR is active all the time.
It's a constant beeping - approximately and consistently one beep per second. I understand that the number of beeps can give you a hint as to what the problem is - 3 beeps for the zone 3 detector, 10 beeps for a power supply problem etc. I have heard the 10 beep warning and the beeps are very close together in time, and then there a pause of around 1 second. I assume that the warning sound I'm currently getting is a zone 1 detector warning.
Fairly sure it's not a tamper warning - once I've got the covers back on and press reset the tamper lights go off.
-
1 hour ago, james.wilson said:
I cant see the panel but is green white reversed?
As far as I know I completely duplicated the wiring from the original installation.
do note that the green and black are almost impossible to differentiate in the photos - it's very dark green.
-
1 hour ago, al-yeti said:
Is the tamper switch closing? Stretch spring a little
If you do some trial and error to prove the cable but putting the yellow and blue together in one terminal and then try it with the alarm red and black at the sensor end and see if and when the panel tries to set normally
You get me?
Pretty sure the tamper function is disabled when I put the covers back on. I will try tweaking the wiring a small you suggest and see what happens.
-
We've had a veritas 8 system for some time and there have been no issues. It is being used in our outhouse/office and uses just a single zone.
Recently we have been remodelling the office and the motion detector ended up being inside a toilet cubicle, so I decided to move the sensor.
The sensor is now wired, as far as I can tell, in exactly the same configuration as before only using a different length of 6-core cable.
Now, when trying to set the alarm, I get a continuous series of single beeps whilst the zone 1 LED is lit red - I assume to show an error with the zone 1 detector, reinforced by the single beeps (instead of multiple beeps).
I have tried shutting off the power and disconnecting the battery to try to reset it to no avail.
A red light is showing in the detector, albeit quite dimly.
Could anyone help me debug it please?
I will swap and see what happens.
Veritas 8 installation bug
in !!..DIY Installers..!!
Posted
Initially I didn't wire it in any other way other than the way the sensor had previously been wired. In debugging I may well have damaged it!
Perfectly competent to do so - I will try that, thanks.