-
Posts
53 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by Mark Rider
-
-
2 hours ago, MrHappy said:
IIRC needs mains to start,
Power it down
Remove the modem connection,
Rainbow ribbon if fitted
bell +
Speaker+
Zem +
Aux + on both tiers of the pcb terminals
Check all the pcb fuses with DVM on buzz (replace any blown one with correct value)
Restart with just the RKP on it, if won't change onto the battery its deffo shagged
think its the same pcb, but but minor sorfware changes which includes app support ?
Ok will do see what happens thanks I let you know
-
5 hours ago, Amps said:
So new battery fitted and still the same
Same faults
Also with the power off you can't do a start with just the battery doesn't seem to do anything at all.
So looks like it's the panel
So question the V10 is the layout much the same on the panel ?
-
3 hours ago, Amps said:
How/where did you manage to download the Pyronix insite software!
From there website . It's good bit of software.
-
well i have a battery tester and have tested it like i said and its ok
No wonder people dont use professionals as there all as arrogant as you.
as i said i have all the tools just wanted some advice as not fully up to speed on alarms
as i work on 800v Porsche Taycans
-
ok lol
well im a High Voltage vehicle tech so know how to measure current and voltage so thats not a problem.
So do you know what voltage should be coming out the PSU ?
also when you disconnect the battery the alarm sounds which it didnt do before but if you turn power off it shuts down with no battery back up .
-
??? how can it be ok then if it has a fault because of low power ?
-
as i have checked the battery. drop test etc powers other stuff ok as well
for got to add the control panel also says the psu power is below 10.38volts
-
Hello
so have had a euro46 for last 3 years installed by my self all been fine
then all of a sudden got faults fault is Battery fault , PSU fault , Low volts, battery critical
so i measure volts on psu thats 20v AC and battery is 13.4 volts so there all good
so not sure why its gone faulty
screen shots of UDL software attached
got no idea where to go now
strange thing is the UDL software isnt showing the volts or current
any help is good thanks very much
-
so have had a pyronix euro 46 for over a year now the push notifications have been ok not always 100%
but now stopped completely im on andriod , no idea why this has stopped
anyone else had this
mark
-
Thanks for all the info chaps been helpful
Mark
-
Now that is a good point right there. Never thought of it that way .
And that has changed my mind now.
240v detector it is then
-
Thanks both.
I will have a look at the texe and the Menvier sensors. I put it by the bed rooms rather than bathroom/kitchen end
Thanks
-
No just add on sensor for my pyronix euro 46
Thanks
-
Fitted my alarm , now want to fit a smoke/heat sensor
What's people views on them it will be in a hallway of a bungalow so what's best smoke or hear sensor and any recommendations of make.
Thanks
Mark
-
Hi I have the pyronix home control app
And was wondering about the my video section.
Does it work and what cameras work with it
I have a hikvison NVR with ip cameras , can't get it working with those anyone actually figured it out as no instructions either for it
Thanks
Mark
-
I didnt say it wasn't easy should take a day to do it in one go as the cabling is peace of cake but as you say whats point in doing the job twice may as well wait until I'm in the room that I'm doing then run the cable.
-
IT ? Nope why do you think that ???
I'm totally renovating my bungalow so each room I do I'm wiring the alarm in to that room
mark
-
Perfect thank you very much.
Will give that a shot.
Just adding sensors as I go and under stand what each item does. so getting there
Thanks very much
-
Didnt think so .
Ar ok I have set the PIR as an intruder. Will try it as an entry route but will that delay the alarm on entry if it was a burglary
Thanks
-
So I'm just playing with my alarm to get head round it have so far fitted bell box, front door contact and hall PIR.
Question is when I go to set the alarm I walk to the panel in the hall I have to walk past the PIR. I go to set the alarm but can't as the PIR is active I have to wait 10 or so seconds for the PIR to deactivate then I can set it. Is that right ? I have read the instructions but can't see anywhere about it.
Anyone any ideas the alarm works fine or once set the PIR will set the alarm off if moving in front of it and have set the final edit as the front door and that works fine.
Any ideas ?
Thanks
Mark
-
Ok so it's a zem 8
Thanks
-
Ok easy to wire up ? How many extra wired zones that give thanks
Mark
-
Oh ok. What do you say then.?
-
Great thanks
Just to confirm
4 wires to contact 2 tamper and 2 power. And run eol on each contact ?
Mark
Euro 46 psu battery fault
in Members Lounge (Public)
Posted
No good won't start with it all disconect