[Help please]

8 hours ago, sixwheeledbeast said:

Comfort LED yes

Do you know how to turn them off ? Have they got jumpers within the shock sensor ? 

[Help please]

1 hour ago, james.wilson said:

the viper will flash like that its a 'comfort' led if you tap them again the led will stop for about 7 sec. Best to have them in this mode its like comfort leds on a bell, shows its powered

Can the led’s be turned off ? 

[Help please]

46 minutes ago, sixwheeledbeast said:

Nope, use the Texecom Impaq ones unless I have to use proper Vipers for replacement (aesthetics/latch line etc)

Mostly wireless shocks now if customer needs perimeter.

They havent been triggered in a very long time maybe since they have been installed. Alarm will set and unset as normal and will trigger if they are bashed or knocked. 

[Help please]

1 hour ago, sixwheeledbeast said:

They flash red all the time with comfort on, latch line is solid light

They only started flashing when i tested they were working the other day. 

[Help please]

I can remove the battery backup and turn the power off to the panel. You think that would reset them ??

[Help please]

Small bit further help. After getting the PIR sensor installed and working. I decided to do a walk test and see if everything was fine and which zones were which.

 

I believe these are shock sensors ? well i gave them a little nudge to see which zone they were in and now they flash red constantly. Anyone any ideas how to get them to stop flashing ???

 

I have set the alarm and unset it ive been into engineer mode and done a reset still they flash ALL NIGHT LONG !!

 

Any further help would be appreciated......

[Help please]

Thanks to all the replies. 
 

PIR now working perfectly few issues I forgot I set the alarm to all the defaults so not knowing the default pin was #### i triggered the tamper and couldn’t shut it down but got it all done in the end. 
 

[Help please]

3 minutes ago, al-yeti said:

Mogadishu is safer to travel to than ardossan 

You would be required to wear a Haz mat suit at all times and that was before COVID-19

 

[Help please]

Iron brew for the hangover. But beer to cause that effect 

 

[Help please]

19 minutes ago, al-yeti said:

I guess I could type it out but I am going to  be lazy , your just getting confused the word eol , ignore it , so then instructions are the same as what I said before

 

 

White and green to tamper terminals

Blue and yellow to alarm terminals

Black is minus - terminal

Red is positive + terminal

 

 

 

Thanks for the help. I owe you a few of these

[Help please]

So don’t put any cables in the EOL screws ? 

[Help please]

2 minutes ago, al-yeti said:

White and green to tamper terminals

 

Blue and yellow to alarm

Black is minus -

Red is positive +

Aux DC fail because probably short it out 

On the new PIR it has two connectors for Alarm and tamper one each with EOL above them what colour in the EOL screw 

 

+ Red

- Black

Alarm EOL ?

Alarm ?

Tamper ?

Tamper EOL ? 
 

thanks for all the help and patience and yes the glass fuse is blown I will replace it 

[Help please]

The kitchen fitter is a friend of a friend so its down to me to pay for it all . The PIR cost £20 i could change it for something similar in spec ? the picture below is the alarm box i took the cover off it 

[Help please]

Lets pretend im stupid  

 

What colour wires go into the pyronix terminals ??

 

And since ive cut the old one off now the panel is saying AUX DC fail ?? Am i better getting a pro into look at it ?

 

[Help please]

Hi all hoping someone on here can help and save me trying to get someone to fix this. We have had a new kitchen installed and the fitters cracked the sensor off the wall and ive got a new one can someone help me ?? which wires go where on the new one ?

 

The sensor on the left is the old one and the sensor on the right is the new one Pyronix KX10DP. Do i need a different PIR sensor ???

 

Any help would be greatly appreciated 

 

Gavin