[Help needed with Wiring Odyssey siren to GSM ALARM]

8 minutes ago, PeterJames said:

Dont take this the wrong way but you need to get some basic electronics knowledge before you start playing around with stuff you dont understand. I gave up because you dont have any idea of what people are trying to explain. 

Thank you for advice

you are alright I'm computer engineering and I'm missing basic of electronics

Currently I need help to get just for this siren to work

I want to know the wire from siren to control panel that I showed how they look like

 

[Help needed with Wiring Odyssey siren to GSM ALARM]

21 minutes ago, PeterJames said:

I give up

Thank you for your help

[Help needed with Wiring Odyssey siren to GSM ALARM]

17 minutes ago, sixwheeledbeast said:

They have an engineer hold off mode and will not be full operation with the lid open.

I Put jack in off for LC stay the same

 

  

17 minutes ago, PeterJames said:

If you use a power supply you have to common up the ov

 

 

[Help needed with Wiring Odyssey siren to GSM ALARM]

2 minutes ago, al-yeti said:

Turn battery on 

Turned on  but still the same

When I wire the siren with 12v and 0V from control panel or from Power Supply 12V DC  it make sound and the green light flashing and than stop wait for trigger from control panel
I tested with mini siren that is work with audio jack (Siren+ , Siren -) it is working normally when there is trigger

something in the linking I have did from control panel to siren is wrong

[Help needed with Wiring Odyssey siren to GSM ALARM]

2 minutes ago, al-yeti said:

Where did you get bell? Is bell tamper closed?

 

Does bell have jumpers you can take picture of

 

[Help needed with Wiring Odyssey siren to GSM ALARM]

15 minutes ago, PeterJames said:

 Either the sounder doesnt work, or the panel isint outputting 12v. If you have wired 12v and gnd and the wired bell to gnd it should have sounded

 

I'm trying now with Power Supply 12V DC

12v  ----------------------------> 12V+

0V ------------------------------> -

 

and from control panel I wired

Siren                               Control panel

Bell ----------------------------> GND

STRB ------------------------> GND

 

nothing happened when I trigger the siren from control panel or PIR trigger

 

[Help needed with Wiring Odyssey siren to GSM ALARM]

4 hours ago, PeterJames said:

Maybe the panel relay is knackered or the bell  its hard to say without looking if yo move the wire frome N/O to common does the bell sound?

Nothing happened

 

3 hours ago, al-yeti said:

Nothing happens when you do what?

when I triger the siren from control panel or when PIR triger

I think I have to use the Siren+ and siren-

I tried

 

Siren                               Control panel

12v  ----------------------------> 12V

0V ------------------------------> GND AND COM

Bell ----------------------------> NO

STRB ------------------------> NO

 

ANd

 

Siren                               Control panel

12v  ----------------------------> 12V

0V ------------------------------> GND AND COM

Bell ----------------------------> COM

STRB ------------------------> COM

 

[Help needed with Wiring Odyssey siren to GSM ALARM]

2 hours ago, al-yeti said:

Bell and strobe would be tied together into the normally open side of the relay , then common relay to 0v , I think lol

The tamper you need to for now ground it in the bell if it allows so it ignores it , I think lol

 

1 hour ago, PeterJames said:

 

Common on the control panel (CPU) links to ground 

 

 

I don't need TMP for now

 

I linked

Siren                               Control panel

12v  ----------------------------> 12V

0V ------------------------------> GND AND COM

Bell ----------------------------> NO

STRB ------------------------> NO

 

Nothing happened

am I wrong in the linking ?

 

[Help needed with Wiring Odyssey siren to GSM ALARM]

14 hours ago, al-yeti said:

Seems as though you can't programme as above 

 

So you need to use

 

0v

+12v

Then the relay for the bell trigger , which drops bell trigger to 0v when siren goes

 

The tamper could be used on a zone in defence mode , look at page 11 , although not a tamper it can act as a 24hr armed zone , but you would have to mess around to make it work 

 

 

 

 

I'm lost in the linking

The control panel wired ports:

*) NO -  Relay port (normal open). It will be triggered when the system is alarming.
*) COM - GND port of relay
*) NC - Relay port (normal close). It will be triggered when the system is alarming.
*) 12V - Positive end of 12V output
*) Zone2 - Wired sensor 2: support both NO and NC
*) GND - GND
*) Zone 1 - Wired sensor 1: support both NO and NC
*) GND - GND

*) There is audio jack for siren S+ S-

 

 

Siren                               Control panel

12v  ----------------------------> 12V

0V ------------------------------> GND

Bell ----------------------------> ?

STRB ------------------------> ?

 

what I have to link for bell and STRB ?

 

 

 

[Help needed with Wiring Odyssey siren to GSM ALARM]

1 minute ago, PeterJames said:

The siren need permanent 12v

Do you mean 12v from control panel is insufficient ?
because Last year I linked with wired siren from different brand with 12 v from control panel of this gsm alarm and it is working great
but with Odyssey 1E I don't know how or where I am wrong

[Help needed with Wiring Odyssey siren to GSM ALARM]

35 minutes ago, al-yeti said:

Unlikely anyone uses that alarm 

 

Anymore pictures or a link to the installation manual ? 

The Manual of Odyssey 1E
http://www.moretonalarms.com/pdf_engineer_manuals/Odyssey.pdf

The Manual of Wolfguard GSM Alarm (this is different model but almost the wired zone are the same)

http://www.wolf-guard.com/app/file/8

 

57 minutes ago, PeterJames said:

Never heard of a wolfguard doesnt look like it has a tamper return, the bell needs a negative trigger that I would guess you can get from N/O on the panel; and adding OV to common  

I tried but nothing happened except the light of the siren is green

[Help needed with Wiring Odyssey siren to GSM ALARM]

Hi All,

I did read many post on the forum before starting this one so please excuse me im repeating someone else question.

 

Im linking Siren Texecom Odyssey E1 With Wolfguard GSM Alarm

I don't know if they work properly

 

Could someone tell me if it's possible to pair this siren with this control panel  and what links I have to follow

 

Any help would be appreciated.