Pat
-
Posts
16 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by Pat
-
-
Scantronic 9752 two keypads,had to remove K02,put panel into installer mode and disconnected K02 whilst still powered up unable to get out of installer mode panel indicates K02 missing, do I need to power down panel and restart to finally delete K02?
-
Panel indicates K02 missing
-
Scantronic 9752 two keypads,had to remove K02,put panel into installer mode and disconnected K02 whilst still powered up unable to get out of installer mode panel indicates K02 missing, do I need to power down panel and restart to finally delete K02?
-
Did try individual wiring each keypad no luck and also finally short wire direct to panel same problem finally tried returning panel to second stage reset factory defualts still same problem enough time wasted on panel. Will be changing to Scantronic 9651 or 9752. Thanks for all help anyway
-
Yes have tried soft reset not sure if one of the the 3 keypads has been damaged during power cut perhaps wire back only 1 keypad at a time and see if this error code goes away?
Was working ok prior to power cut I do know keypads after power cut and reset were working to engineer code?
any help appreciated don't whant to change panel and keypads
-
I have a scantronic 816 with 3 ( 930) keypads after a recent power cut had to replace 7Ah battery, have done this and performed customer and installer ( first stage reset). Problem I have is the following message on keypads "KPAD BUS TAMPER" and PID Bus tamper. Could anyone advise as to what might be problem?
-
Thanks for help did get the keyfob learned,started with a 723 & 727r the 723 would learn on the RFX08 but with a RFX16 both keyfobs operated. Any one know why the 727r may not work with the RFX08?
-
With the RFX in "_ _" having pressed select is this not the learn mode?
-
I have a 9751 Scantronic which I would want to add a wireless panic button. I have obtained a RFX08 expander with a 727r four button telecommand key fob.Prior to fitting I have tried putting the RFX in learn mode via a temporary 12VDC supply using a battery.The RFX on powering up lights "88" with a short beep and on pressing the select buton shows "_ _" . Pressing the 727r key fob its LED flashes on and off but I cannot get it to talk to the RFX.The RFX just stays in "_ _" without even a single tone even if it could not learn the 727r any help would be much appreciated?
-
Sorry see photo
-
Can anyone help identify the keypad in the picture it operates via keypad and token reader, need to source user instructions ? many thanks for any help
-
When would you use the look the down on this Pir?
-
Can some one explain the use of the Look down being either diabled or enabled on the pir of the Honeywell DT7450 DUAL TEC?
-
Looking for some advice on new build bungalow, wanting to fit a wireless alarm initially during build to protect property in first fix works allowing Pir’s to be located not to impede works and easily rearranged, but with the view to have the system incorporated in project final fit.
What would be the views on say a Scantronic i-on16 which is totally wire free with the end station powered via an inverter and a standby 12v 80Amp Gel battery for the inverter until such time mains power available or alternatively a Texecom Premier Elite 12-w live which would have the benefit of 8 Ricochet enabled wireless zones with another 4 zones for wired devices which can used in the second fix?
Scantronic 9752 K02 missing
in Guest Forum
Posted
Powered down panel added fresh battery powered up again no fault this time with K02 missing.Given the keypad was originally removed whilst still powered panel was still probably looking for KO2, resolved anyway thanks for help