Keef Posted May 25, 2021 Share Posted May 25, 2021 (edited) Hi all, following a few garage break-ins on our estate lately, I decided to change to a Rio from a single zone so I can add a PIR. Everything went ok, the system detects the Rio, Rio set to slave via link 4, but I can only get one zone to work.All are set to intruder. zone 8 Roller shutter contact - works normally zone 7, PIR - Nothing zone 6, Door contact, Nothing I did have the Door Contact working on zone 2 at one time when I tested it before installing. It is set to address 3 I have searched online for guides on installing nd programming, but can find very little. Photo is from when I tested it. Thanks for reading, Keith Edited May 25, 2021 by Keef Quote Link to comment Share on other sites More sharing options...
MrHappy Posted May 26, 2021 Share Posted May 26, 2021 Do you have both resistors & cables in terminals ? Quote Mr Veritas God Link to comment Share on other sites More sharing options...
james.wilson Posted May 26, 2021 Share Posted May 26, 2021 Why are you using it as a slave. That's for shunting etc Quote securitywarehouse Security Supplies from Security Warehouse Trade Members please contact us for your TSI vetted trade discount. Link to comment Share on other sites More sharing options...
al-yeti Posted May 26, 2021 Share Posted May 26, 2021 36 minutes ago, james.wilson said: Why are you using it as a slave. That's for shunting etc Lol I wondered why he was doing that Quote Link to comment Share on other sites More sharing options...
Keef Posted May 26, 2021 Author Share Posted May 26, 2021 (edited) 8 hours ago, al-yeti said: Lol I wondered why he was doing that By the sound of it I am doing it in error. I followed another post I found online. I have only cut one side so I can easily reattach it it. Hopefully you lot can tell me the correct way to do it. There are only 1k resistors in the unused zone terminals, plus 2x1k on the other 3 zones Thanks, Keith Edited May 26, 2021 by Keef Quote Link to comment Share on other sites More sharing options...
james.wilson Posted May 26, 2021 Share Posted May 26, 2021 The 1k restistors should be in the devices not at the rio Quote securitywarehouse Security Supplies from Security Warehouse Trade Members please contact us for your TSI vetted trade discount. Link to comment Share on other sites More sharing options...
Keef Posted May 27, 2021 Author Share Posted May 27, 2021 32 minutes ago, james.wilson said: The 1k restistors should be in the devices not at the rio Sorry, not worded very clearly. The resistors are at the 2 contacts and the PIR, only the unused zones have them at the Rio Quote Link to comment Share on other sites More sharing options...
Nova-Security Posted May 27, 2021 Share Posted May 27, 2021 11 hours ago, Keef said: I have only cut one side so I can easily reattach it it. Before anything remake link 4 Quote www.nova-security.co.uk www.nsiapproved.co.uk No PMs please unless i know you or you are using this board with your proper name. Link to comment Share on other sites More sharing options...
Keef Posted May 27, 2021 Author Share Posted May 27, 2021 9 hours ago, Nova-Security said: Before anything remake link 4 Link 4 remade and still the same Quote Link to comment Share on other sites More sharing options...
Nova-Security Posted May 27, 2021 Share Posted May 27, 2021 Whats the panel you are using, RIO is addressed as 3 so the circuits would start at 1031 The wiring looks like its going to ciruit 1 and 2 on the rio but the leg of circuit 1 looks like there isnt anything in it on the picture. In your first post you mention zones 6.7.8 but the EOL resistors are in 6,7,8 and where are you getting the power for the PIR from? Quote www.nova-security.co.uk www.nsiapproved.co.uk No PMs please unless i know you or you are using this board with your proper name. Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.