paulbaker1954 Posted September 27, 2020 Share Posted September 27, 2020 Got a Gardtec 595 panel linked to the Risco wireless module. Two of the wireless shock sensors are triggering false tamper alarms and is now occurring at least twice a day. Have tried changing the sensor battery but still the same. Any othe ideas to fix? Alternatively I could just get rid of them but I can’t figure out how to unconnected them from the wireless receiver, anyone know how this is done. I tried simply taking batteries out but that didn’t help Quote Link to comment Share on other sites More sharing options...
MrHappy Posted September 27, 2020 Share Posted September 27, 2020 adjust spring (s) / the case is damaged to remove from system you need to program the circuits off Quote Mr Veritas God Link to comment Share on other sites More sharing options...
Hillbilly Posted September 27, 2020 Share Posted September 27, 2020 Like all risco tat over time issues like this appear for no reason at all.I had this and had to replace them. Had this issue with a wireless door contact last week randomly tampering and replaced it. It is only in contacts that has been the tamper issue over time. Quote Link to comment Share on other sites More sharing options...
al-yeti Posted September 27, 2020 Share Posted September 27, 2020 2 hours ago, Hillbilly said: Like all risco tat over time issues like this appear for no reason at all.I had this and had to replace them. Had this issue with a wireless door contact last week randomly tampering and replaced it. It is only in contacts that has been the tamper issue over time. Well many systems got the querks , I got my first hkc wirreess contact where the reed inside sticks , but only one , Honeywell had loads in passed that send a low RF batt signal no matter what you do , texe always got firmware going so you know how it is Risko have these problems long time now Quote Link to comment Share on other sites More sharing options...
MrHappy Posted September 27, 2020 Share Posted September 27, 2020 26 minutes ago, al-yeti said: Well many systems got the querks , I got my first hkc wirreess contact where the reed inside sticks , but only one , Honeywell had loads in passed that send a low RF batt signal no matter what you do , texe always got firmware going so you know how it is Risko have these problems long time now The one way radio devices are rock solid Gardtec controls are quirky, but workable Wisdom / Agility, my life is too short... Quote Mr Veritas God Link to comment Share on other sites More sharing options...
aissecur Posted September 27, 2020 Share Posted September 27, 2020 As per previous comment, adjust the spring & ensure the battery is at a healthy level some sit on a spacer, so make sure that’s not causing any issues Or that the spring is not bent (has that before) if you want to remove from the zone you need the engineer code & it’s done on the program zones (first option when in engineers mode) Quote Link to comment Share on other sites More sharing options...
al-yeti Posted September 27, 2020 Share Posted September 27, 2020 2 hours ago, MrHappy said: The one way radio devices are rock solid Gardtec controls are quirky, but workable Wisdom / Agility, my life is too short... Wisdom hardcore messed up , although I sold a few brand new boxed that someone gave up on Quote Link to comment Share on other sites More sharing options...
MrHappy Posted September 27, 2020 Share Posted September 27, 2020 36 minutes ago, aissecur said: As per previous comment, buy a dog ? Quote Mr Veritas God Link to comment Share on other sites More sharing options...
james.wilson Posted September 27, 2020 Share Posted September 27, 2020 Does anyone rate risco anymore? I know the past and how it was 1 way would you use it out vs anything else? Quote securitywarehouse Security Supplies from Security Warehouse Trade Members please contact us for your TSI vetted trade discount. Link to comment Share on other sites More sharing options...
paulbaker1954 Posted September 28, 2020 Author Share Posted September 28, 2020 (edited) Thanks all for comments. If I can’t fix them and get new senders I have the install manual for the senders that says set the receiver to write mode but I don’t know how do this. The receiver is a separate square white box wired in to the gardtec panel. if anyone has the install instructions for the receiver they can share that would be fab Edited September 29, 2020 by MrHappy removed Risco's file Quote Link to comment Share on other sites More sharing options...
paulbaker1954 Posted September 29, 2020 Author Share Posted September 29, 2020 Now it’s pissing memoff Peogrammed sensors to off in main panel (program zone types) and still triggers a tamper alarm frequently Tried taking battery out and this triggers another error code with an “L” after it when trying to set the alarm. Any ideas please Quote Link to comment Share on other sites More sharing options...
MrHappy Posted September 29, 2020 Share Posted September 29, 2020 "L" means lost, "delete the circuit off " aka remove the transmitter in the zex menu 91-98 or whatever +no ? Quote Mr Veritas God Link to comment Share on other sites More sharing options...
paulbaker1954 Posted September 29, 2020 Author Share Posted September 29, 2020 8 hours ago, MrHappy said: "L" means lost, "delete the circuit off " aka remove the transmitter in the zex menu 91-98 or whatever +no ? Hi and thanks for the reply but I am still a bit confused. I have the programming manual for the panel but can’t find the program option to remove the transmitter . You refer to the zex menu but not exactly sure what you mean . Soory to be dim but am not super familiar with this setup Quote Link to comment Share on other sites More sharing options...
al-yeti Posted September 29, 2020 Share Posted September 29, 2020 29 minutes ago, paulbaker1954 said: Hi and thanks for the reply but I am still a bit confused. I have the programming manual for the panel but can’t find the program option to remove the transmitter . You refer to the zex menu but not exactly sure what you mean . Soory to be dim but am not super familiar with this setup You using right access code? Quote Link to comment Share on other sites More sharing options...
Hillbilly Posted September 29, 2020 Share Posted September 29, 2020 You need to enter eng code then user code.... scroll to Zones....enter 50 Yes and work your to disable wireless zones etc. Quote Link to comment Share on other sites More sharing options...
paulbaker1954 Posted September 30, 2020 Author Share Posted September 30, 2020 19 hours ago, Hillbilly said: You need to enter eng code then user code.... scroll to Zones....enter 50 Yes and work your to disable wireless zones etc. Sorry there ain’t no zone 50 it’s a gardtec panel with a a separate wireless box wired in to the main panel Quote Link to comment Share on other sites More sharing options...
al-yeti Posted September 30, 2020 Share Posted September 30, 2020 2 hours ago, paulbaker1954 said: Sorry there ain’t no zone 50 it’s a gardtec panel with a a separate wireless box wired in to the main panel You menu menu 50? Quote Link to comment Share on other sites More sharing options...
paulbaker1954 Posted September 30, 2020 Author Share Posted September 30, 2020 29 minutes ago, al-yeti said: You menu menu 50? Menu 50 is zone wiring (EOL) etc Quote Link to comment Share on other sites More sharing options...
paulbaker1954 Posted October 1, 2020 Author Share Posted October 1, 2020 23 hours ago, paulbaker1954 said: Menu 50 is zone wiring (EOL) etc Thanks all got it figured out now Quote Link to comment Share on other sites More sharing options...
Hillbilly Posted October 2, 2020 Share Posted October 2, 2020 I meant when it says programme zones go 50 yes. Quote Link to comment Share on other sites More sharing options...
al-yeti Posted October 2, 2020 Share Posted October 2, 2020 1 hour ago, Hillbilly said: I meant when it says programme zones go 50 yes. I think gets it now lol Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.