Jump to content
Security Installer Community

Risco wireless shock sensors tamper issue


Recommended Posts

Got a Gardtec 595 panel linked to the Risco wireless module. Two of the wireless shock sensors are triggering false tamper alarms and is now occurring at least twice a day.


Have tried changing the sensor battery but still the same.

 

Any othe ideas to fix?

 

Alternatively I could just get rid of them but I can’t figure out how to unconnected them from the wireless receiver, anyone know how this is done. I tried simply taking batteries out but that didn’t help

Link to comment
Share on other sites

2 hours ago, Hillbilly said:

Like all risco tat over time issues like this appear for no reason at all.I had this and had to replace them.

Had this issue with a wireless door contact last week randomly tampering and replaced it.

It is only in contacts that has been the tamper issue over time.

 

Well many systems got the querks , I got my first hkc wirreess contact  where the reed inside sticks  , but only one , Honeywell had loads in passed that send a low RF batt signal no matter what you do , texe always got firmware going so you know how it is 

 

Risko have these problems long time now 

Link to comment
Share on other sites

26 minutes ago, al-yeti said:

Well many systems got the querks , I got my first hkc wirreess contact  where the reed inside sticks  , but only one , Honeywell had loads in passed that send a low RF batt signal no matter what you do , texe always got firmware going so you know how it is 

 

Risko have these problems long time now 

 

The one way radio devices are rock solid

 

Gardtec controls are quirky, but workable

 

Wisdom / Agility, my life is too short...

 

 

 

 

 

Mr? Veritas God

Link to comment
Share on other sites

As per previous comment, adjust the spring & ensure the battery is at a healthy level 

some sit on a spacer,  so make sure that’s not causing any issues Or that the spring is not bent (has that before) 

 

if you want to remove from the zone you need the engineer code & it’s done on the program zones (first option when in engineers mode) 

Link to comment
Share on other sites

2 hours ago, MrHappy said:

 

The one way radio devices are rock solid

 

Gardtec controls are quirky, but workable

 

Wisdom / Agility, my life is too short...

 

 

 

 

 

Wisdom hardcore messed up , although I sold a few brand new boxed that someone gave up on 

Link to comment
Share on other sites

Thanks all for comments. If I can’t fix them and get new senders I have the install manual for the senders that says set the  receiver to write mode but I don’t know how do this. The receiver is a separate square white box wired in to the gardtec panel.

 

if anyone has the install instructions for the receiver they can share that would be fab 

 

Edited by MrHappy
removed Risco's file
Link to comment
Share on other sites

8 hours ago, MrHappy said:

"L" means lost,

 

"delete the circuit off " aka remove the transmitter in the zex menu 91-98 or whatever +no ?

Hi and thanks for the reply but I am still a bit confused. I have the programming manual for the panel but can’t find the program option to remove the transmitter . You refer to the zex menu but not exactly sure what you mean .

 

Soory to be dim but am not super familiar with this setup 

Link to comment
Share on other sites

29 minutes ago, paulbaker1954 said:

Hi and thanks for the reply but I am still a bit confused. I have the programming manual for the panel but can’t find the program option to remove the transmitter . You refer to the zex menu but not exactly sure what you mean .

 

Soory to be dim but am not super familiar with this setup 

You using right access code?

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.