Jump to content
Security Installer Community

Texecom Premier Elite Keypad Mapping & Tamper


Al H

Recommended Posts

Afternoon

 

Help please. Texecom Premier Elite 24 new installation which I’m setting up some of the zones to help understand its operation. I will be adding another 8 zones later. All zones are EOL and one per zone.

 

However I’ve got an issue with front door contact which is a CQR SC570 (SEE IMAGE) (one on back door as well). It’s differs in that I’ve wired it to the keypad next to the door and connected to the Zone 1 at the back of keypad.  This I’ve mapped to zone 17.  I do have a 8 zone expander connected to the panel motherboard although nothing wired into it as yet.

 

This zone 17 now shows a tamper alarm (see image). Ive isolated the switch and confirmed its resistances are 2.2k closed and 7k open (same as its twin on back door zone 1)

 

I know there’s also a tamper error on zone 5 which is a viper shock, but I’ve not looked at this yet.

 

I suspect its to do with the keypad configuration which I’m missing something. Any ideas please?

5BCF6710-8E0C-4785-88C2-2F1BDB7ACC18.jpeg

5CEB9BFB-B8C5-4789-8BE7-293FC8AF3A4A.jpeg

9F7ABFC0-8930-47C5-B91B-D6EE5EC41A95.jpeg

Link to comment
Share on other sites

15 minutes ago, Al H said:

Afternoon

 

Help please. Texecom Premier Elite 24 new installation which I’m setting up some of the zones to help understand its operation. I will be adding another 8 zones later. All zones are EOL and one per zone.

 

However I’ve got an issue with front door contact which is a CQR SC570 (SEE IMAGE) (one on back door as well). It’s differs in that I’ve wired it to the keypad next to the door and connected to the Zone 1 at the back of keypad.  This I’ve mapped to zone 17.  I do have a 8 zone expander connected to the panel motherboard although nothing wired into it as yet.

 

This zone 17 now shows a tamper alarm (see image). Ive isolated the switch and confirmed its resistances are 2.2k closed and 7k open (same as its twin on back door zone 1)

 

I know there’s also a tamper error on zone 5 which is a viper shock, but I’ve not looked at this yet.

 

I suspect its to do with the keypad configuration which I’m missing something. Any ideas please?

imageproxy.php?img=&key=2baeda2b516ecee0imageproxy.php?img=&key=2baeda2b516ecee0imageproxy.php?img=&key=2baeda2b516ecee0

5BCF6710-8E0C-4785-88C2-2F1BDB7ACC18.jpeg

5CEB9BFB-B8C5-4789-8BE7-293FC8AF3A4A.jpeg

9F7ABFC0-8930-47C5-B91B-D6EE5EC41A95.jpeg

You need engineer

Link to comment
Share on other sites

Hi James. I originally had 2 wires from keypad zone 1 Alarm terminals. I did not have the tampers connected !  I have now connected as per photo but get the display Active but red sign on wintex.. See images. 

A79C592C-003C-409B-9047-EF976742B5F1.jpeg

B765662F-384A-4A69-9950-51485A142818.jpeg

8C6F9382-F957-4854-923E-F0C211D87174.jpeg

Link to comment
Share on other sites

No matter what i do with the resistors it always shows on the keypad display greater then 65k ?  What is the correct way to wire from the keypad zone, it has 2 A and 2T terminals? I’m thinking its probably the programming I’m missing ?

Link to comment
Share on other sites

1 hour ago, Al H said:

No matter what i do with the resistors it always shows on the keypad display greater then 65k ?  What is the correct way to wire from the keypad zone, it has 2 A and 2T terminals? I’m thinking its probably the programming I’m missing ?

But it's not what he saying , now it seems you don't know how to wire contact?

 

What's happens if you place resistor across keypad terminals?

 

What happens if you connect cable remove contact and put resistor across pair going to keypad ?

 

What's keypad say then , as then you can follow order of fault finding if you can't test cable directly or have a meter

 

Unless it's something to do with how you have mapped the zones 

Link to comment
Share on other sites

1 hour ago, Al H said:

Hi James. I originally had 2 wires from keypad zone 1 Alarm terminals. I did not have the tampers connected !  I have now connected as per photo but get the display Active but red sign on wintex.. See images. 

A79C592C-003C-409B-9047-EF976742B5F1.jpeg

B765662F-384A-4A69-9950-51485A142818.jpeg

8C6F9382-F957-4854-923E-F0C211D87174.jpeg

Why do you have a cable pair and resistors connected in keypad?

  • Upvote 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.