Moataz Posted October 25, 2017 Author Share Posted October 25, 2017 @Galaxy Guy no I am testing on another one sorry for not clarifying Quote Link to comment Share on other sites More sharing options...
Moataz Posted October 26, 2017 Author Share Posted October 26, 2017 @Galaxy Guyu Guys please I nead help with this antidrill sensor sc100 now the tamper sensor is working correctly once I click the button the state convert from open to closed but the vibration sensor alarm still open and I cannot set my system coz of it so please guys I will share the connection from both sides panel and sensor and please help. Regards, Here is the pics Quote Link to comment Share on other sites More sharing options...
Moataz Posted October 26, 2017 Author Share Posted October 26, 2017 @al-yeti sorry bro , I thought that @Galaxy Guy who replied to me I didn't notice the name , I need your recommendations bro Quote Link to comment Share on other sites More sharing options...
al-yeti Posted October 26, 2017 Share Posted October 26, 2017 It's ok , no one else here notices me except Norman ,he gives everyone therapy Quote Link to comment Share on other sites More sharing options...
GalaxyGuy Posted October 26, 2017 Share Posted October 26, 2017 You need to start again with the wiring. It's too messy. Solid cores are too brittle too. Spend £15 on alarm cable. Connect three cores only at the panel. Say: +12v - brown 0v at the zone - blue The zone input - green. At the sensor, connect Brown to +12v Blue to 0v. Now loop a wire from 0v in the sensor and connect it to NC. Connect a 1k resistor from NC to C Connect another resistor between C and T1. Connect the green wire to T2. 1 Quote Link to comment Share on other sites More sharing options...
datadiffusion Posted October 26, 2017 Share Posted October 26, 2017 (edited) 1 minute ago, GalaxyGuy said: Spend £15 on alarm cable. I don't know, out of the frying pan, etc... Based on the fact the top 100 hits for alarm cable on ebay. amazon etc... etc... or the local DIY shed usual DIYers outlet of choice will be CCA Edited October 26, 2017 by datadiffusion Quote So, I've decided to take my work back underground.... to stop it falling into the wrong hands Link to comment Share on other sites More sharing options...
al-yeti Posted October 26, 2017 Share Posted October 26, 2017 2 hours ago, GalaxyGuy said: You need to start again with the wiring. It's too messy. Solid cores are too brittle too. Spend £15 on alarm cable. Connect three cores only at the panel. Say: +12v - brown 0v at the zone - blue The zone input - green. At the sensor, connect Brown to +12v Blue to 0v. Now loop a wire from 0v in the sensor and connect it to NC. Connect a 1k resistor from NC to C Connect another resistor between C and T1. Connect the green wire to T2. Dude what you on about He's got the role jumpers still in and using resistors , unless I confused , but if not you need to start again Instructions far to messy Quote Link to comment Share on other sites More sharing options...
al-yeti Posted October 26, 2017 Share Posted October 26, 2017 7 hours ago, Moataz said: @al-yeti sorry bro , I thought that @Galaxy Guy who replied to me I didn't notice the name , I need your recommendations bro You don't need resistors at panel end if your using the resistors in the detector to start with , then might be T2 and NC at detector end and a zone on panel Of course I might be confused I just guessing standard Honeywell positions when eol used Quote Link to comment Share on other sites More sharing options...
Moataz Posted October 26, 2017 Author Share Posted October 26, 2017 @Galaxy Guyy @al-yeti I know this also and when I connect the external resistors I don put the jumpers , and btw I applied honeywell standard , the two diagrams in their installation guide but it doesn't work for me Quote Link to comment Share on other sites More sharing options...
al-yeti Posted October 26, 2017 Share Posted October 26, 2017 24 minutes ago, Moataz said: @Galaxy Guyy @al-yeti I know this also and when I connect the external resistors I don put the jumpers , and btw I applied honeywell standard , the two diagrams in their installation guide but it doesn't work for me So show pictures of what you have? Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.