ryan042000 Posted April 12, 2013 Share Posted April 12, 2013 Reinstallin a delta 5 due to panel change any one know how to wire these into a texecom elite 48 This is a pic of the terminals Link to comment Share on other sites More sharing options...
sjsturner Posted April 12, 2013 Share Posted April 12, 2013 Theres no pic showing ryan. What terminals are there? Link to comment Share on other sites More sharing options...
ryan042000 Posted April 12, 2013 Author Share Posted April 12, 2013 1. Siren hi-off 2. V+ 3. 0v 4. Siren 5 batt - 6. Batt + 7. Tamp 8. Tamp 9. St + 10. St- Link to comment Share on other sites More sharing options...
Paul. Giles Posted April 12, 2013 Share Posted April 12, 2013 Seems self explanatory? Link to comment Share on other sites More sharing options...
matthew.brough Posted April 12, 2013 Share Posted April 12, 2013 Seems self explanatory? +1 www.securitywarehouse.co.uk/catalog/ Link to comment Share on other sites More sharing options...
ryan042000 Posted April 12, 2013 Author Share Posted April 12, 2013 Yes i thought so to but the siren just starts up when power is applied to terminal 2&3 and the tamper switch is closed a red and green led energise when thamper switch is closed bit confused im used to adt bells Link to comment Share on other sites More sharing options...
sjsturner Posted April 12, 2013 Share Posted April 12, 2013 Soz just got back. So you have wired " bell " from texe panel to " siren " on bell box yeah? Link to comment Share on other sites More sharing options...
ryan042000 Posted April 12, 2013 Author Share Posted April 12, 2013 Yeh if i can figure out the hold off and the sab im sorted got the tamper sorted byt im not sure if theres somthing wring with the sab do you know if this needs a pos trig or neg Link to comment Share on other sites More sharing options...
sjsturner Posted April 12, 2013 Share Posted April 12, 2013 How have you connected this up? Link to comment Share on other sites More sharing options...
sjsturner Posted April 12, 2013 Share Posted April 12, 2013 Judging from what i can gather you need Terms 1= 0v 2= 12v 3= 0v 4= bell trig 5+6 you know what to do with that! 7= 0v 8= tmp return 9= 12v 10= strobe You can put 0v in term 3 and link terms 3 and 1 and 7 together in bell box Also put 12v pos in term 2 and link 2 and 9 together Then your bell trig goes in term 4 Your tmpr return in 8 Strobe trig in 10 Link to comment Share on other sites More sharing options...
Lwillis Posted April 12, 2013 Share Posted April 12, 2013 If I remember correctly the delta bells are a +ve trigg. Unless there's a jump link on them to change that. Link to comment Share on other sites More sharing options...
sjsturner Posted April 12, 2013 Share Posted April 12, 2013 Ive never even seen one so im not sure but if thats the case then hes applying a neg currently so the trig isnt there. He says it powers up ringing i reckon he has 12v in term 1 instead of 0v If the trig is + i take it hel have to use a relay? Not installed a prem or is there prog +12v output? Link to comment Share on other sites More sharing options...
ryan042000 Posted April 12, 2013 Author Share Posted April 12, 2013 Yeh the prems can switch from pos trig to neg ( sab/ scb mode) Ill try your sugestions and get back to you tomorrow hopefully it works Link to comment Share on other sites More sharing options...
sjsturner Posted April 12, 2013 Share Posted April 12, 2013 Dont hold your breath! I havent personally installed either but thats how i would wire it. Going off what you have shown me, good luck Link to comment Share on other sites More sharing options...
Lwillis Posted April 12, 2013 Share Posted April 12, 2013 I've got a delta in the van ill have a look if you get stuck on it . Link to comment Share on other sites More sharing options...
ryan042000 Posted April 12, 2013 Author Share Posted April 12, 2013 Dat would be great lwillis then i could note it down Link to comment Share on other sites More sharing options...
Lwillis Posted April 12, 2013 Share Posted April 12, 2013 I'll have a proper look in the morning but found this online . Fairly straight forward; fault (not used) fault (not used) tamp (0v) tamp (tamp back to panel) - Tamper return 0v (ov) - Neg hold 12+ (12v) - + hold eng (not used) rtest (not used) str (- strobe trigger) - self explanatory hoff (- Bell trigger) - bell neg bt- (Battery -) Batt bt+ (Battery +) - Batt PZ1 not sure about these as someone has taken them off - PZ will stand for Piezo PZ2 - ditto. Link to comment Share on other sites More sharing options...
sjsturner Posted April 12, 2013 Share Posted April 12, 2013 I'll have a proper look in the morning but found this online . Fairly straight forward; fault (not used) fault (not used) tamp (0v) tamp (tamp back to panel) - Tamper return 0v (ov) - Neg hold 12+ (12v) - + hold eng (not used) rtest (not used) str (- strobe trigger) - self explanatory hoff (- Bell trigger) - bell neg bt- (Battery -) Batt bt+ (Battery +) - Batt PZ1 not sure about these as someone has taken them off - PZ will stand for Piezo PZ2 - ditto. Delta 6? Link to comment Share on other sites More sharing options...
Lwillis Posted April 12, 2013 Share Posted April 12, 2013 Might be , just looked up delta. Tbh I'd not refit one and use a texecom bell Link to comment Share on other sites More sharing options...
sjsturner Posted April 12, 2013 Share Posted April 12, 2013 Same here! He showed terms top of page^ We use oddy 3e Link to comment Share on other sites More sharing options...
ryan042000 Posted April 13, 2013 Author Share Posted April 13, 2013 Mines a delta 5 should go with tex bells know them inside out just love my delta 5 lol Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.