alterEGO Posted January 27, 2013 Share Posted January 27, 2013 As James, new battery at that age. If that does not clear the fault then you can try the monitor hardware, think its a local setting, not sure its in a wintex menu. Quote Link to comment Share on other sites More sharing options...
sixwheeledbeast Posted January 27, 2013 Share Posted January 27, 2013 No of course, but I assume the OP is not brain dead.Not brain dead, but I was assuming the OP has no idea tho. I wouldn't check a battery with the built-in voltage readings. You are correct about the "Monitor Hardware Shuffle", had to do this a couple of times. Quote Link to comment Share on other sites More sharing options...
GrahamUK33 Posted January 27, 2013 Author Share Posted January 27, 2013 Thanks for your help and advice guys, I have now ordered a new battery. Â I will let you know the outcome once the battery has been installed. Quote Graham twitter: ithorizon1 http://www.ithorizon.co.uk Link to comment Share on other sites More sharing options...
GrahamUK33 Posted January 30, 2013 Author Share Posted January 30, 2013 I have fitted the new battery yesterday, logged in via Wintex and it looks like everything is back to normal. No more Alerts on the screen either. Â Thanks for all your help and advice guys. Quote Graham twitter: ithorizon1 http://www.ithorizon.co.uk Link to comment Share on other sites More sharing options...
ARJ Posted June 23, 2015 Share Posted June 23, 2015 Ive got a fault on a Premier 24. I put a new battery in 3 months ago after a battery fault and the customer has called me back as its appeared again. Investigation shows that the battery is only holding 7v but then checking the charging voltage its only 6.7v. I have 13.2 v on the Aux and bell outputs but the battery leads are only pumping 6.7v down them. Keypad diagnosis confirms this when reading system status. Without any adjustable pot on the PCB or blown fuse, how can I adjust the charging voltage back to 12v ?? Quote A nearly retired previous installer ! Link to comment Share on other sites More sharing options...
james.wilson Posted June 23, 2015 Share Posted June 23, 2015 did it have a knackered battery in the past? Quote securitywarehouse Security Supplies from Security Warehouse Trade Members please contact us for your TSI vetted trade discount. Link to comment Share on other sites More sharing options...
ARJ Posted June 23, 2015 Share Posted June 23, 2015 did it have a knackered battery in the past? Yes, i think the previous battery whilst fairly new got totally drained in a long duration power cut. Quote A nearly retired previous installer ! Link to comment Share on other sites More sharing options...
james.wilson Posted June 23, 2015 Share Posted June 23, 2015 its usual that a poorly serviced system kills its charger circuit. New panel id say Quote securitywarehouse Security Supplies from Security Warehouse Trade Members please contact us for your TSI vetted trade discount. Link to comment Share on other sites More sharing options...
ARJ Posted June 23, 2015 Share Posted June 23, 2015 New install in 2011, had 3 batteries since but think it had a long outage around 2013. Last fitted a batt in March, another one today. I'll verify with Tex Tech support tomorrow as customer is a neighbour so a bit awkward to quote £100 for a new PCB even though outage wasnt my fault ! Thanks for the quick responses. Quote A nearly retired previous installer ! Link to comment Share on other sites More sharing options...
charlie6 Posted June 23, 2015 Share Posted June 23, 2015 Might be worth checking the battery charging current, nominally 500mA or thereabouts. Also a current limiting resistor gone high value, look for burn marks around resistors in that area. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.