Jump to content
Security Installer Community

Concept - Tamper & Power indicators lit


Recommended Posts

Guest godfrey

I have recently moved into a house with an alarm fitted in 1993.

The control panel is Concept "Advanced Microprocessor Control".

It worked fine for the first couple of months.

Recently, during any power cut the internal alarm sounder sounds, (but not the external strobe) and the keypad will not respond. Once power is restored, the control panel functions OK, but the security code has returned to the default code and needs to be reprogramed.

During some decorating we have unscrewed some PIR panels from wall (not disconnected). These are back in place. We have also had the power off again. However the control panel now shows Power and Tamper lights and will not respond to keypad. The Zone lights continue to light up when there is any movement in the zone.

I only have the basic card with user instructions. Please can anyone provide advice or user manuals?

Many thanks

Link to post
Share on other sites

The battery is faulty in the main panel, you will need to power down the panel, (remove battery, the mains supply).

Then power backup, mains first then New Battery. enter 0123.

Close all tamper (replace lid on panel etc) press reset the panel should now go back to day mode, if not then will need to get someone (alarm company) to look at it.

The basic card is the user manual!!!

Regs

jpaul

There are no stupid questions, but there are a LOT of inquisitive idiots.

Link to post
Share on other sites
  • 14 years later...
On 08/02/2004 at 18:27, j.paul said:

The battery is faulty in the main panel, you will need to power down the panel, (remove battery, the mains supply).

Then power backup, mains first then New Battery. enter 0123.

Close all tamper (replace lid on panel etc) press reset the panel should now go back to day mode, if not then will need to get someone (alarm company) to look at it.

The basic card is the user manual!!!

Regs

jpaul

M

 

On 08/02/2004 at 18:27, j.paul said:

The battery is faulty in the main panel, you will need to power down the panel, (remove battery, the mains supply).

Then power backup, mains first then New Battery. enter 0123.

Close all tamper (replace lid on panel etc) press reset the panel should now go back to day mode, if not then will need to get someone (alarm company) to look at it.

The basic card is the user manual!!!

Regs

jpaul

 

Same problem here.  We have put in a new battery and entered 0123 it’s now gone back to day mode.

 

How do I set my own code in 

Link to post
Share on other sites
3 hours ago, Jean Felthouse said:

M

 

 

Same problem here.  We have put in a new battery and entered 0123 it’s now gone back to day mode.

 

How do I set my own code in 

Get user manual?

Link to post
Share on other sites
1 hour ago, Jean Felthouse said:

Can’t find the user manual for this his alarm.    Thanks anyway

Might be 

 

Press prog

Enter existing code 

Press 8

Four zones light up

Enter new code

Press reset

 

New code should work , this is an old user manual I have I don't know how many panels are called concept but might be same

Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.