Andy cb
-
Posts
52 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by Andy cb
-
-
6 minutes ago, Logan said:
We cant tell you in the general public area for ovious reasons
Is this my next step
-
11 minutes ago, Logan said:
Default user code is ##REMOVED##
But I haven’t reset anything yet I have the lid of the external and all powered down still
what should be my next step
-
Just now, Logan said:
Yes there is engineer reset and code reset. DO NOT DO ENGINEER RESET your system will have to be completely reprogrammed if you do that
Ok so I used to have user code but that doesn’t seam to work anymore how do I reset to give me back default user and engineer coax to I can work on the system
-
Just now, Logan said:
Yes. ALSO BEWARE THIS WILL WIPE THE PROGRAMMING.
Now I read on another forum that there is a type of reset that doesn’t wipe programming
-
21 minutes ago, Logan said:
Yes. Make sure not to lose it
Ok done that thanks Logan
so I have powered down entirely
main fuse battery backup and extreme rain siren battery
I have wired in new keypad as old 9930 was dead
can I now default reset to give me back engineer code?
and if so am best to use jumpers to short kick start and nvs pins
-
4 minutes ago, james.wilson said:
yes
Does it simply pull out
-
1 minute ago, james.wilson said:
no its not a resistor its a jumper
No I know that but I’d it in the area I marked in the second picture
-
I’ve read policy and spoken to insurance i can maintain myself and as said before I do get minimal discount but something is better than nothing
-
-
Yeah I can see the battery but not how to disconnect it with out pretty much taking whole unit out
-
-
1 hour ago, al-yeti said:
Double blag
What do you mean by that al-yeti
-
If I added perimeter sensors I’d have to look into expanders and things and the new sensors would have to be wireless as I’ve just finished refurbish and decorating the house
-
6 minutes ago, whistle said:
FFS, it’s like bind leading the feckin blind in here these days.
Your point being whistle all genuine non confusing advice welcome ed
-
7 minutes ago, Logan said:
I learned about the master blaster as i tested the system not knowing there was a master blaster when i moved in and i couldnt hear anything for the rest of the day. It also shredded a towel that was in the loft
Losing hearing not good but shredding towel sounds cool
-
2 minutes ago, Logan said:
At least you don't have a master blaster in the loft and a quad bellbox outside. You can hear it go off from over a mile away
Opps
-
If I added perimeter sensors I’d have to look into expanders and things and the new sensors would have to be wireless as I’ve just finished refurbish and decorating the house
-
It’s something I’m thinking of but reality is there is someone in the house almost all the day it’s more to keep insurance happy and a bit more piece of mind I live in a safe area as safe as can be
-
15 minutes ago, Logan said:
What PIRs do you plan to install. I reccomend pyronix pet PIRs HOWEVER pet PIRs are NOT fool proof. You can still get false alarms from something such as a cat jumps on a table
If you have pets i recommend using perimeter protection
The system already has optex rx 40 just swapping to the same but pet tolerant as I now have a small cat
-
4 minutes ago, Logan said:
Yes.
Great thanks
-
My plan is to pull main fuse this I understand cuts the high voltage then disconnect external battery back up then open lid and pull fuses and battery back up
then default reset
power down and wire in new keypad
check system working and power down again and swap out pir’s
-
2 minutes ago, Logan said:
If you remove the lid the system might give a tamper (cant silence as keypad doesn't work) also it needs to be disconnected when doing any wiring to the system
Hold on I’m getting confused
your telling me to disconnect battery and fused in the box after pulling main fuse but now you telling me can’t remove lid I case of tamper and busted keypad
so how am I ment to power down and reset without opening the lid and without a working keypad??
-
1 minute ago, Logan said:
The layout of panel is the same as the 9651 just a different circuit board just trying to show you where to disconnect the battery
That’s fine can I not take off the red and black connections on the battery itself it needs changing anyway
-
Keypad and pir upgrade for scantronic 9651
in !!..DIY Installers..!!
Posted
It was direct line guys I explained that I had inherited the system when I moved in I’d had a local installed come and reset it and service it when I moved in so I could use it and they where happy with that and I had received around a £50 per year discount on my premium simply by telling them I have an alarm fitted
touch wood I’ve never had situation where it has ever needed to be brought into question but thank you all for your help and concerns system is all back and working just fine now and with the upgrades I’d asked for help and advice on
I would have got my local installer to do it but I think he has retired as I haven’t been able to get in touch for a couple of years and can’t fined another at a sensible price point