grantc
-
Posts
67 -
Joined
-
Last visited
-
Days Won
2
Content Type
Profiles
Forums
Events
Downloads
Gallery
Blogs
Posts posted by grantc
-
-
Any him ptz's I've fitted have needed additional power.
The camera comes with either a PSU or Poe injector in the box.
Grant
Hik*
-
Some more junk if you want it?
The first 2 boxes are decoys. Dunno if you collect them?
There is a keypad inside the gardtec panel - not sure if it works?
The old Scanny apparently still works and was regularly maintained.
Grant
-
Ok
will look them up!
-
Yeah no probs, will get a price when I get a minute.
Cheers
-
This too if you want it?
-
Logan....
Ripped this out this morning.
Is it of any interest to you?
I can post when I get a chance if you cover postage.
Grant
-
Pyronix V2 GSM
Pretty sure I have one I'd sell if you're interested.
Grant
-
I actually own a MK2 fiesta XR2 funnily enough.
Have done for about 13 years.
Has sat in the garage most of those
-
Go to assign keypads and readers and check all other addresses apart from 0.
I suspect one is programmed as a reader/keypad.
Set them to unused.
0 should be a keypad.
Come out of engineers mode and that should sort it hopefully.
Grant
-
1
-
-
Thanks James.
In that case, press and hold D till it says enter security code.
Put in 2000.
Press no till you get to address and make it 1
Press A to save
Keypad should be working.
-
Your working keypad should be address 0.
Got to assign keypads and readers and select keypad address 1. Make this a keypad.
Then you have to access a hidden menu on the non working keypad and address it as 1 - Admin - ok to give out this info?
That should get the 2nd keypad working.
The panel has to be powered up on mains first to recognise the Digi WiFi so it shows in the menu.
-
1
-
-
Does it come out of engineer mode?
It should tell you the issue if it doesn't.
Keypad will have went red as you created a keypad tamper.
Won't go green again till it's out of engineer mode/keypad tamper resolved.
-
How old the battery?
-
Delete all serial no.s of RF zones
-
1
-
-
Switch Comms format to not used.
You using Digi WiFi for app only?
Go through WiFi settings within Comms to connect to router etc
-
Re install the app?
Has your subscription ended?
-
21 hours ago, Leemh99 said:
Its not just the zones, there's outputs hanging of it all over the place. AV, speakers, some sort of pager system, detector leds, the list goes on.. Defaulting is going to be a nightmare.
Fair enough, sounds like a nightmare....
Did it happen last thing on a Friday by any chance? :-)
-
Can't you view zone types/descriptions in menu 21 take note then bite the bullet and default?
-
Free subscription came to an end?
-
Why are you using 2 buttons to unset b?
The unlock button should be setup for unset any
-
2 boards on them. Bell wired off the small PCB at bottom.
Wire tamper across on of the onboard zones and program accordingly.
-
Post a pic of the actual tag your using
-
I'll ask the obvious, are you holding the tag up to the top right of the screen?
When you add a user, it says enter code then you present tag. Is that what you are doing?
-
The pic looks like the correct tags.
Does it beep when you hold the tag up?
Do IP PTZ's need extra power
in CCTV & Access Control
Posted
Powering the camera as the Poe port on the back of the NVR doesn't put out enough power?