Jump to content
Security Installer Community

mark auto

Trade Full Member
  • Posts

    80
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by mark auto

  1. Partly the issue - plenty of work but its more bits and bats of additions rather than full installs. We also use CASH software so anything we do remotely on the portal would need to be cross referenced - so I think any savings on engineer time would be lost again in admin time.
  2. In what ways do you consider it pays for itself? We looked at it the other day and for us its probably not worth the investment right now, are we missing something?
  3. Gutter/downpipe idea may be do-able, havent been to the house for a while so would have to see if its feasible or not, good idea though
  4. Need to install cctv on a new build domestic, chipboard floors etc so lifting the floor isnt happening, and the external walls are insulated with board type insulation i believe also, so fishing up cavities would be very difficult. Added to this, we want to keep the cameras at a reasonable level, ie not just slapped on soffits, this house is on a slope so it appears to be 2 storeys from the front, but its actually 3 storeys when viewed from the rear. I toyed with one of the hik dome cameras that had built in wifi, but it seemed very unstable even sitting on my desk, it would work for a few hours through hik connect (which i think is awful BTW), then it would drop off, never to return until i defaulted the camera and started again, putting it back on our wifi network etc. I have thought about using IP cameras with POE injectors/PoE switches, network bridges etc, ie drill through a wall near a socket, camera outside, PoE inside, wireless link internally to the router, or use TP links or similar, but it all seems a bit messy. Is there an easy way of achieving this that im missing?
  5. I think people generally just dont think things through logically. The problem of "people might forget the code" is solved in the simplest way possible with no consideration of the negatives
  6. Makes a change from the code being written on the keypad in permanent marker.......
  7. CIE equipment should not be visible from outside the premises anyway CIE equipment should not be visible from outside the premises anyway
  8. looking at your screenshots i would do the following: *uncheck "entry exit 2" on your hallway *turn off auto part arm on areas A and B *turn on "part arm silent" for area A *change your area arm type from timed to entry/exit when arming, enter code (or fob without auto yes), press part, press yes. See how you go with that
  9. wireless is ok but if your doing renovations i would say cable the alarm. texecom premier panels can send texts down a phone line via a com 2400 module, or you can use a com ip or com wifi unit linked to your broadband router to send notifications through an app
  10. my mistake, we monitor mains fail as standard really so i often forget thats a condition of reducing the standby time Are you Nigel Farage?
  11. PD6662 states the same 12hours for grade 1 and 2, but reduces grade 3 and 4 to 24hrs (from 60 in 50131), like i said i was always told the EN requirements were to cover countries with unreliable power grids, ours doesnt need so long personally i dont think 8 hours is long enough, 12 is much better
  12. Some EU countries have much less reliable power grids than our own, so i think they're just covering worst case scenario
  13. Is this ALL ID biscuits are no longer being made? ID+ included?
  14. open the main control panel, silence the alarm, locate the 12volt aux supply to the detectors (red and black wires), disconnect those, replace the pir, the reconnect them, close up the panel and reset the system. should be good to go! and yes, its a bit overkill, but for £0 i dont think you can complain
  15. red v+ black v- yellow/green - T1 & T2 blue/white - C & NC take all the jumper pins off the fault, tamper and alarm pins too
  16. Blimey James, that was quick! Thanks!
  17. thanks, will do. would admin/moderator be able to change my screen name to something slightly more...ahem......professional? or is it easier to just abandon the account and start over?
  18. hi everyone, joined this forum years ago and used to check in regular, not been on for a couple of years hoping to gain access to the trade only section for details on standards etc, but the trade link just seems to bring up an error, anyone help me on this? Mark
  19. mark auto

    Errrr

    why cant people just take a bit more time and care over the install? nice neat installs make it so much easier in the long run
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.