Prodigious Posted October 22, 2017 Share Posted October 22, 2017 Anyone got a idea on programming cause and affect on these panels? I’m new to them but basically I have a rather big premises with several I/O units with which one of the units I do not want to be triggered when the system goes into fire alarm state but only to be triggered when one certain call point or smoke is triggered. The I/0 unit is in same room as the call point and smoke any tips or help would be great that guys Quote Thrones Link to comment Share on other sites More sharing options...
sjsturner Posted October 23, 2017 Share Posted October 23, 2017 You got the mx pro software and lead? Quote Link to comment Share on other sites More sharing options...
Prodigious Posted October 23, 2017 Author Share Posted October 23, 2017 13 hours ago, sjsturner said: You got the mx pro software and lead? Yes my friend Quote Thrones Link to comment Share on other sites More sharing options...
sjsturner Posted October 23, 2017 Share Posted October 23, 2017 So in your loop list, edit your io device into a new output group ( default is 199) so make it let's say 10. then go into your "edit output cause and effect tab" right click and select "add output group" create the group number 10 then select input point , then pick your call point or smoke from the list, to add more devices simply right click on your new group and select "add input event" to add more input devices. you can do it by altering zones and creating zone rules also but it depends specifically on what your trying to achieve to be honest. Quote Link to comment Share on other sites More sharing options...
Prodigious Posted October 23, 2017 Author Share Posted October 23, 2017 I think I’m with you.. so will give it a go, basically it’s a 3 loop panel 80/100 devices used up in each loop, but the request is that one particular I/O unit which is in the boiler room is programmed in such a way that the relay does not change when the system goes into fire condition from all devices apart from two Devices which are the smoke and call point is in the same boiler room, when these are triggered the relay needs to trigger thanks Quote Thrones Link to comment Share on other sites More sharing options...
sjsturner Posted October 24, 2017 Share Posted October 24, 2017 And I assume when they trigger (devices in boiler room) all other outputs will trigger? To raise alarm? Or no Quote Link to comment Share on other sites More sharing options...
sjsturner Posted October 24, 2017 Share Posted October 24, 2017 The way described above would only make the IO operate when your boiler room CP or SD goes off, you can select pre alarm ect too, when the SD and CP activate, all the other devices (sounders and relays in group 199 will still go into fire as normal) Quote Link to comment Share on other sites More sharing options...
Prodigious Posted October 24, 2017 Author Share Posted October 24, 2017 5 hours ago, sjsturner said: And I assume when they trigger (devices in boiler room) all other outputs will trigger? To raise alarm? Or no Yes indeed so 4 hours ago, sjsturner said: The way described above would only make the IO operate when your boiler room CP or SD goes off, you can select pre alarm ect too, when the SD and CP activate, all the other devices (sounders and relays in group 199 will still go into fire as normal) Yes that’s exacaly what I want Quote Thrones Link to comment Share on other sites More sharing options...
Prodigious Posted October 24, 2017 Author Share Posted October 24, 2017 22 hours ago, sjsturner said: So in your loop list, edit your io device into a new output group ( default is 199) so make it let's say 10. then go into your "edit output cause and effect tab" right click and select "add output group" create the group number 10 then select input point , then pick your call point or smoke from the list, to add more devices simply right click on your new group and select "add input event" to add more input devices. you can do it by altering zones and creating zone rules also but it depends specifically on what your trying to achieve to be honest. Absolutely worked a treat and first time! Thank you very much, saved me a load of time and far less stress thanks again Quote Thrones Link to comment Share on other sites More sharing options...
sjsturner Posted October 24, 2017 Share Posted October 24, 2017 Your welcome mate Quote Link to comment Share on other sites More sharing options...
durcanservices Posted December 6, 2017 Share Posted December 6, 2017 (edited) Any chance of getting a copy of the MX Pro config tool? I’ve had my old laptop stolen from the van a few weeks ago and haven’t worked on a MX Pro panel for a while. Got a few C&E to edit and don’t fancy working it through the panel. Thanks! ##REMOVED CONTACT DETAILS## Edited December 6, 2017 by sixwheeledbeast Removed contact details, please read the forum rules before posting . Thanks. Quote Link to comment Share on other sites More sharing options...
datadiffusion Posted December 7, 2017 Share Posted December 7, 2017 (edited) And further to the above, if you came here to post a load of 'lol, me too!' tut on year old threads to bulk up your profile then quietly ask for illegal copies of software before disappearing, think again. Edited December 7, 2017 by datadiffusion Quote So, I've decided to take my work back underground.... to stop it falling into the wrong hands Link to comment Share on other sites More sharing options...
sjsturner Posted December 7, 2017 Share Posted December 7, 2017 You got an illegal copy Stu?? i had to ******* pay for Mine!!! :-) the logo software cost me a bit too. let me know what other Bootleg programs you got for me Quote Link to comment Share on other sites More sharing options...
datadiffusion Posted December 7, 2017 Share Posted December 7, 2017 I've got; Windows 3000 Borland 286 Emulator FAST Floppy Copy V2.3 Menvier LINELOAD 1.2 (Note: Spanish language version) Quote So, I've decided to take my work back underground.... to stop it falling into the wrong hands Link to comment Share on other sites More sharing options...
sjsturner Posted December 7, 2017 Share Posted December 7, 2017 Donde Quote Link to comment Share on other sites More sharing options...
datadiffusion Posted December 7, 2017 Share Posted December 7, 2017 All uploaded to Member Downloads (Paywall Area) Quote So, I've decided to take my work back underground.... to stop it falling into the wrong hands Link to comment Share on other sites More sharing options...
sjsturner Posted December 7, 2017 Share Posted December 7, 2017 Scorchio! Gracias Quote Link to comment Share on other sites More sharing options...
Chris bell Posted August 23, 2022 Share Posted August 23, 2022 Any help would be appreciated mxpro 5 need to programme a old people's home so any flat gets a fire input only sounds that flat and a sounder In office thanks Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.