Jump to content
Security Installer Community

Karizma control panel blank....


John 4

Recommended Posts

hi ,

i have just cut a wire to a  PIR on my alarm system........actually just knicked one of the coloured wires within cable......

the internal siren sounded and it seems all power to other PIR's and main panel has been lost ....cable wires are all connected now.

 

any ideas ....

thanks 

Link to comment
Share on other sites

Hi

yes your correct...

fuse blown 

now it wants the engineer code which I thought was #### enter but that's not working ..

so panel working but need the eng code 

again any ideas 

and thanks for reply

 

hiw much is a service ??

Edited by sixwheeledbeast
Removed code
Link to comment
Share on other sites

The installer would use there own code in the system.

We do not give out codes, manuals or defaulting information here for security reasons.

 

If you can't contact the original maintainer, I would recommend you call a few local companies and inquire about a service.

Karisma's are quite an old panel now, I have known even well maintained ones to have iD biscuits fail and NVM issues.

Link to comment
Share on other sites

10 minutes ago, John 4 said:

I don't know original installer ...

there must be some way of putting in a new engineer code .....

thats all it seems to need .....

anyone know how ??

Well you will need to default the system which may mean reprogramming it , you could pay someone to do once over and provide you with it , but if it's cost excersice then may reflect what your trying to protect meaning it's low priority 

Link to comment
Share on other sites

in order to change the engineer code (if unknown) it will mean a full default of the system and  would require it being fully re- programmed  from scratch.

Unless you are fully ofay with alarms and competent I strongly suggest this is carried out by a competent alarm engineer.

 

Edited by aissecur
spelling mistake
Link to comment
Share on other sites

5 hours ago, PSE said:

You could get someone to default the engineer & user codes only, no need for a full default. A decent alarm co / engineer could default them within no time at all. 

Are you sure? I didnt think you could with ADE panels, its been a long time since I did any programming mind.

Link to comment
Share on other sites

Ok it's asking for the engineer code which according to manual should be #### but for some reason that's not working ....

so looks like I'll have to get alarm specialist out to take a look .......

shame I thought someone on this site could give me a solution.......

 

Edited by datadiffusion
Code hidden AGAIN. OP please stop putting engineer codes in public as per forum rules.
Link to comment
Share on other sites

 

3 minutes ago, John 4 said:

so looks like I'll have to get alarm specialist out to take a look .......

 

there's Karizma, Karizma+ & a Karzima UDL

 

even if we fitted it we'd have little interest in supporting it, 

 

You'll be lucky if you can find someone who'll supports the cabling

 

 

 

 

  • Upvote 1

Mr? Veritas God

Link to comment
Share on other sites

32 minutes ago, John 4 said:

Ok it's asking for the engineer code which according to manual should be #### but for some reason that's not working ....

 

This code is the default code, which we ask you not to post as per forum rules. It will have been changed by the original installer.

Can you see the potential problem if it was not changed...?

 

32 minutes ago, John 4 said:

so looks like I'll have to get alarm specialist out to take a look .......

 

This is an obsolete system prone to sudden failure. I have replaced many, usually they fail at 3am with sirens blazing, or perhaps during a holiday.

 

32 minutes ago, John 4 said:

Shame I thought someone on this site could give me a solution.......

 

The solution is to default the system, though not the best one. We don't give that information out on here, you would rightly be very annoyed if a burglar could simply log in here and gain access to your system, surely?

  • Upvote 2

So, I've decided to take my work back underground.... to stop it falling into the wrong hands

 

Link to comment
Share on other sites

1 minute ago, John 4 said:

You can find the engineer code within 2 minutes but clearly whoever  installed the alarm has changed that default code 

 

anyway this site has given me no useful answers 

 

so I'll be withdrawing from it 

very disappointing 

Glad we could be of service

Link to comment
Share on other sites

11 minutes ago, John 4 said:

You can find the engineer code within 2 minutes but clearly whoever  installed the alarm has changed that default code 

 

anyway this site has given me no useful answers 

 

so I'll be withdrawing from it 

very disappointing 

Excellent you answered your own question, £104 question .

 

Ps , means you found the manual and know how to default the panel and can programme it , easy as that 

Edited by al-yeti
  • Like 1
Link to comment
Share on other sites

13 minutes ago, John 4 said:

You can find the engineer code within 2 minutes but clearly whoever  installed the alarm has changed that default code 

 

anyway this site has given me no useful answers 

 

so I'll be withdrawing from it 

very disappointing 

The useful answer was already given below in red

 

39 minutes ago, datadiffusion said:

 

This code is the default code, which we ask you not to post as per forum rules. It will have been changed by the original installer.

Can you see the potential problem if it was not changed...?

 

 

This is an obsolete system prone to sudden failure. I have replaced many, usually they fail at 3am with sirens blazing, or perhaps during a holiday.

 

 

The solution is to default the system, though not the best one. We don't give that information out on here, you would rightly be very annoyed if a burglar could simply log in here and gain access to your system, surely?

 

Link to comment
Share on other sites

4 hours ago, PeterJames said:

Are you sure? I didnt think you could with ADE panels, its been a long time since I did any programming mind.

 

Yes, Karizma can be done, default user and engineer only. There is a choice of P pins that do a specific job. that all I’m saying in public. 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.