Jump to content
Security Installer Community

Gardtec 360 / 370


Recommended Posts

i think the bwf might be changing something to sir

;)

Nah dont burst my bubble :whistle:

LOL.

not at all, credit where it`s due ........... same with Arfur and the "fast mon."

Probably only 5 real engineers on the site ATM.

Link to comment
Share on other sites

The 360 and the 370 were completely different panels.

Are you sure you are resetting it properly?. You could link out the bell tamper at the panel , if it clears then the fault is at your repair or the bell box.

Link to comment
Share on other sites

Hi Guys

Thnks very much for all of your help/suggestions, I found a none contacting wire in the cable jointing block I had used for the repair.

Simple, though Oh so frustrating.

Again Thanks a LOT

Kevin

Kevin

Can you mark the correct answer on the thread and reward the points to the person that helped.

Press the green button to the right of the relevant post

securitywarehouse Security Supplies from Security Warehouse

Trade Members please contact us for your TSI vetted trade discount.

Link to comment
Share on other sites

I wouldnt have bothered posting about it if it didnt ............

get it from Maplins - then it`s easier to take it back there the next day to get one that fits*

* yuasa 2.1A will do it.

your very correct Paul,

l perhaps you should NOT have bothered to post, the 3amp (aka old 2.6 amp shape) will fit if sat on its side as long as all the cables enter the cabinet from the top.

Oxo,

only the metal version 370 supports a Gardtec Pro Digi, afiak for systems to be monitored today the software would not support even the very old sequential signal confirmations.

from manual -:

ProDigi Communicator (Standard, AV & AV Serial)

It is possible to use a ProDigi Communicator with a Gardtec 370 Metal version.

Connection details for the ProDigi are shown below.

i never used many and no metal versions of it. but i'd think in factory default it's not engineer reset (would be a bit pointless in bells only under old 'rules').

imo mainly used for the very cheapest 'bells only' systems and in the plastic format, so possible 9but i'd doubt0 if this panel is set to engineer reset as such.

Arfur

If you think education is difficult, try being stupid!!!!

Link to comment
Share on other sites

your very correct Paul,

l perhaps you should NOT have bothered to post, the 3amp (aka old 2.6 amp shape) will fit if sat on its side as long as all the cables enter the cabinet from the top.

.

Arfur

your right, you shouldnt have posted - it won`t fit, end of story

Link to comment
Share on other sites

Oxo,

only the metal version 370 supports a Gardtec Pro Digi, afiak for systems to be monitored today the software would not support even the very old sequential signal confirmations.

Never said it did,your ovaltine got drugs in it?

Link to comment
Share on other sites

Never said it did,your ovaltine got drugs in it?

Ovaltine is on Rashions - orders of Mrs Mo cold2.gif

we were discussing Eng Rst, and why that post

Arfur

If you think education is difficult, try being stupid!!!!

Link to comment
Share on other sites

we were discussing Eng Rst, and why that post

Arfur

you were discussing it, no-one else was, slightly confusing.

so who's the other four with me then, lol

clue - the`re all called Paul.

Link to comment
Share on other sites

you were discussing it, no-one else was, slightly confusing.

clue - the`re all called Paul.

you obviously missed the point,

age of panel = very unlikely ER selected on a bells systems? need i really say more or how much of a upstart in this game you really are?

so, sort of short for 'a-paul-ing' boom! boom!

sorry, i'll get me coat

Arfur

If you think education is difficult, try being stupid!!!!

Link to comment
Share on other sites

Archived

This topic is now archived and is closed to further replies.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use.